JA-82K control panel installation manual - 2 - MKH51103
Contents:
1 Control panel architecture.................................. 3
1.1 Required system configuration 3
2 Preparing the control panel for installation ........ 3
3 Control panel main board................................... 3
3.1 Main board terminal description: 3
3.2 Hard-wired inputs on the main board 4
3.3 Installation of additional hard-wire input modules 4
3.4 Radio module installation 4
3.5 Y,X,V communicator module installation 4
3.6 Control panel memory chip 4
3.7 Wired keypad connection 4
3.8 Control panel resetting 5
4 Control panel power supply ............................... 5
4.1 Backup battery connection 5
4.2 Power supply connection 5
4.3 Powering-up the control panel for the first time 5
5 OASiS wireless devices .....................................6
5.1 Enrolling wireless devices to the control panel 6
5.2 Testing enrolled wireless devices 6
5.3 Signal strength measuring 6
5.4 Erasing enrolled devices 6
5.5 Enrolling the control panel to UC and AC modules 6
6 Control panel programming ............................... 6
6.1 Exit delay time 7
6.2 Entrance delay time 7
6.3 Alarm duration time 7
6.4 PGX and PGY functions 7
6.5 Changing telephone numbers in maintenance mode 7
6.6 Radio interference indication 7
6.7 Radio communications supervision 7
6.8 RESET enabled 7
6.9 Enrollment to a sub control panel for setting control 7
6.10 Master code reset 8
6.11 Enrollment to other devices (UC, AC) 8
6.12 Setting (Arming) without an access code 8
6.13 Triggered-detector indication 8
6.14 Confirmation of intruder alarms 8
6.15 Exit delay beeps 8
6.16 Exit delay beeps while partially setting (arming) 8
6.17 Entrance delay beeps 8
6.18 Setting (arming) confirmed by wired-siren chirp 8
6.19 Sirens always sound during audible alarms 8
6.20 Wireless siren alarm enabled (IW and EW) 9
6.21 Bypass user approval 9
6.22 Final-door detectors 9
6.23 Partial setting (arming) or system splitting 9
6.24 Automatic summer time (daylight saving time) 10
6.25 Pulse reaction of tamper sensors 10
6.26 Operating the PG outputs using 8 and 9 10
6.27 Permanent alarm status display 10
6.28 Tamper alarm if unset 10
6.29 Recording PG output activation to memory 10
6.30 Engineer reset 10
6.31 Social alarm feature 10
6.32 Annual check notification 10
6.33 Only single alarm indication 11
6.34 Setting (arming) by service code 11
6.35 Audible panic alarm 11
6.36 Higher control-panel receiver-sensitivity 11
6.37 Access by code plus card 11
6.38 Audible 24 hour intruder alarm 11
6.39 Service mode only with service and user code 11
6.40 Device reactions and section assignment 11
6.41 Code/card reactions and section assignment 12
6.42 Enrollment by keying in production codes 12
6.43 Automatic setting / unsetting schedule 12
6.44 Changing the service code. 12
6.45 Go to maintenance mode 12
6.46 Setting the internal clock 12
6.47 Editing keypad text 13
6.48 Recommended settings 13
7 Operating the system.......................................13
7.1 The system keypad 13
7.1.1 Keypad indicators: ..................................................13
7.1.2 LCD display.............................................................13
7.1.3 Keypad display sleep-mode....................................13
7.1.4 Keys ........................................................................13
7.1.5 Functions beginning with the key........................13
7.2 Programming access codes and cards 13
7.3 Setting and unsetting (arming/disarming) the system 14
7.4 Maintenance Mode 14
7.4.1 Displaying which user/card positions are occupied 14
7.4.2 Bypassing devices ..................................................14
7.4.3 Protecting a car near the system ............................14
8 Operating/programming the system by PC...... 14
9 Basic guidance for installers ............................ 14
10 Trouble-shooting ..............................................15
11 Control panel technical specifications.............. 16
12 Control panel programming sequences........... 17
13 Programming access codes and cards............ 20
This manual is valid for control panel JA-82K
The control panel can be configured by a PC running OLink software.
