Manual Jablotron JA-80V (page 5 of 10) (English)

555056

Zoom out

Zoom in

1/10

The JA-80V LAN / PSTN line communicator - 5 - MKA51202

Phone number memory M

ec Event

1 2 3 4 5 6 7 8

15 External communication fault S S S S S S S

16 External communication restored

17 Fault S S S S S S S

18 Fault no longer present

19 Mains dropout longer than 30 minutes S S S S S S S

20 Mains dropout

21 Mains restored

22 Discharged battery S S S S S S S

23 Battery OK

24 Switching to Service Mode

25 Leaving Service Mode

26 PGX ON/OFF

27 PGY ON/OFF

28 Radio communication jamming present S S S S S S S

29 Internal communication fault S S S S S S S

30 Internal communication restored

31 Communication test

32 Unconfirmed alarm

• Factory-default report assignment: S = SMS, C = call, SC = SMS followed by a call

• The SMS information about a new picture on the server is sent to all phone numbers which are set to get reported event number 01 “Intruder

alarm - instant”. This information contains a link to the new picture on the server.

5.3.1. Assigning events to be reported by SMS to a particular

mobile phone number

To link events to being reported by SMS, enter:

82 M ec x

where

M phone number memory 1 to 8

ec event code 01 to 32 (see the above table)

x 0 = no SMS report, 1 = SMS report

Example: if 82 8 03 1 is programmed and a fire alarm is triggered (event

03 in the table), it will be reported by SMS to the phone number stored in

memory M8

5.3.2. Assigning events to be reported by phone call to a particular

phone number

To link events to being reported by phone call, enter:

83 M ec x

where

M phone number memory 1 to 8

ec event code 01 to 32 (see the above table)

x 0 = no phone call, 1 = call

Example: if 82 1 03 1 is programmed and a fire alarm is triggered (event

03 in the table), the phone number stored in memory M1 will be called

and if the call is answered, a siren sound will be heard.

Notes:

 Phone call reports are mostly used as an audible notification to alert

the user of a detailed report sent by SMS

 If both SMS + call reports are enabled for events, the SMS is sent

first and then the number is called afterwards. But total priority is

given to ARC reports if enabled (see 7.1 )

5.3.3. SMS/phone call communication checking period

A regularly sent communication checking SMS report and/or phone call

to a telephone can be enabled as event code ec=31 (see table in 5.3).

This sequence programs how often the checking report should be

performed:

84 hhmm

where

hh hours (00 to 24) to wait after the last SMS/phone call

report

mm minutes (00 to 59) to wait after the last SMS/phone call

report

Notes:

 The communication checking report is not sent if the system is in

service mode

Factory default setting: 24 hours from the last report

5.4. SMS text editing

The communicator contains various text strings which are used to create

SMS reports and also SMS instruction text. These text strings cannot be

changed from the system keypad, but they can be edited by Comlink

software, via the Internet (www.GSMLink.cz

) or by sending the following

SMS instruction:

code_TXT_n,text,n,text,......n,text

where

code is a valid access code (e.g. factory defaults: 8080, 1234)

_ is a space

TXT instruction to edit texts

n text number (0 to 611 see the following table)

, comma (or full stop)

text the new text (max. 30 characters) which will replace the former

text. It is invalid to enter a comma or a full stop inside the text

string, but a space is valid within the text string

Notes:

• A single TXT instruction can change multiple texts (limited only by the

maximum length of a single SMS)

• the communicator is not case-sensitive and it is recommended to use

only English ASCII characters (some networks do not support non-

English national characters)

• the communicator creates SMS reports with 5 parts: installation name,

event description, source (code or device) number (01 to 50), source

name, time and date

• the maximum possible length of an ASCII SMS is 160 characters (only

70 characters for national characters). If this length is exceeded, the

report is sent as multiple SMSes

Examples: if the service code is 8080 then the SMS instruction:

8080 TXT 20,key fob Bob,21,Key fob Jane

changes the description (name) of the key fobs enrolled to addresses 20

and 21

8080 TXT 605,heating on,606,heating off

edits the text of the two instructions used to command the heating to be

switched on and off by the PGX output (the PGX output must be

programmed to have an ON/OFF function)

5.5. Enabling reporting to phones

Event reports can be enabled as follows:

800 all SMS and call reports disabled

801 all SMS and call reports enabled

802 all reports enabled except reports of setting and unsetting

by users 41 to 50 (i.e. their codes, cards and key fobs). This

allows setting and unsetting done by report recipients (owners,

bosses, etc.) not to be reported.

803 all SMS and call reports enabled if ARC1 is not responding

804 all SMS and call reports enabled if ARC2 is not responding

Factory default setting: 801 all reports enabled

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80V in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80V

Jablotron JA-80V User Manual - Dutch - 11 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80V Manual

Product: