554835
18
Zoom out
Zoom in
Previous page
1/22
Next page
Installation manual: Oasis security system JA-80K - 18 - MKE51801
MM is the month (01 to 12)
YY is the year (00 to 99)
Note: The internal clock can also be adjusted in maintenance mode.
Example: On 30 June 2012 at 17:15 enter:
4 17 15 30 06 12
After the control panel is powered up, the clock is set to 00 00 01 01 00.
12.47. Editing keypad text
The names of devices and programmable outputs as displayed
on the keypad unit can be edited as follows:
Pressing and holding the ? key (in service mode) enters text
editing mode and the name of the device enrolled to address
01 is then displayed with a flashing cursor on the first text
character.
Key functions:
and text scrolling (see table)
1 and 7 character-selection
(A,B,C,D.......8,9,0)
4 and 5 cursor control (left/right)
2 delete selected character
# exit editing (& save changes)
List of editable text:
text Description
01: to 50: Devices
Names of devices in addresses 01 to 50
Control panel
Name of control panel (e.g. displayed if its cover
is opened)
Keypad
Name of hard-wired keypad
Communicator
Name of the communicator in the control panel
Master code
Name of the master code
01: to 50: Code
Names of user codes
ARC Code
Names of ARC code
Service code
Name of the service code
PGX and PGY
Names of programmable outputs
OASIS JA-80
The default text displayed in operating mode if
no other text needs to be displayed. If erased
then nothing will be displayed.
Notes:
Only capital letters can be entered.
The length of text is limited to the length of the display.
The text is only stored in the keypad used for editing (different
keypads in the system can show different text if desired).
Text is stored in the non-volatile memory of keypads, so power
disconnection will not erase any stored text.
Convenient text editing is possible using a PC running Comlink
software.
Besides device names, keypads also use so-called internal text such
as “service”, “maintenance mode” etc, and this text can also be edited
via Comlink software by selecting “Settings” on the menu and then
“keypad text”.
After editing keypad text using Comlink software, all keypads
(including wireless ones) must be connected to the digital bus to save
the changes to the keypad units by clicking on the OK button in the
software.
Factory default setting: in addresses 01 to 50 there is the text
“Device”. Other default text: “Control panel”, “Keypad”,
“Communicator”, “Master code”, users 01 to 50 “Code”,”ARC
Code”, “Service code”, “PGX”, “PGY” and “OASIS JA-80”.
13. Operating the system
The Oasis system can be operated locally using a keypad or
a keyfob and it can also be operated remotely by mobile phone
or the Internet (if equipped with a suitable communicator).
13.1. The system keypad
Indoor keypads model JA-80F (wireless) or JA-80E (wired) can
be used to operate and program the system. Both keypad types
provide the same functionality:
13.1.1. Keypad indicators:
ABC setting (arming) status of sections – if all sections are
set then all these indicators (A B & C) are lit.
flashing = alarm, with the simultaneous display of alarm
details on the LCD, e.g.:
Alarm
03: Kitchen
constantly lit = fault – details are displayed by pressing
the “?” key
power. Constantly lit = mains ok. Flashing = no mains,
control panel powered by back-up battery only.
13.1.2. LCD display
The 1
st
line displays the status: triggered detector, Service
mode etc. In standby mode, it shows the text “OASIS JA-80”
(editable, see 12.47).
The 2
nd
line displays the name of a device.(e.g. 01: Main Door
etc.). The text can be edited, see 12.47.
Displaying the status of detectors and programmable
outputs: Details on permanently triggered detectors (e.g. open
windows) and the status of the PGX and PGY outputs can be
displayed by pressing the ? key.
13.1.3. Keypad display sleep-mode
In operating mode, the wireless keypad unit displays the
system status for 20 seconds (if battery-powered) after the last
interaction with a user, and then goes into sleep mode. Pressing
any key, triggering the keypad input or opening the keypad’s flip
cover re-activates the display.
13.1.4. Keys
0–9 digital code entry
function sequences
# escape
ABC hot key for setting the entire system (all sections A, B &
C)
A hot key for setting section A (e.g. afternoon partial setting
of the garage)
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80K in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80K

Jablotron JA-80K User Manual - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info