Manual Jablotron JA-80K (page 17 of 22) (English)

554835

Zoom out

Zoom in

1/22

Installation manual: Oasis security system JA-80K - 17 - MKE51801

of the remote control are pressed

simultaneously, they will trigger a panic alarm

a detector – the PG output copies the status of

the detector or it generates a pulsed switching

event when the detector is triggered. The

detector also effects the control panel which

responds with a natural reaction. Only one

detector should be programmed to a PG output

ON/OFF reaction and should not be combined

with keyfob or keypad control as the detector

repeats its status every 9 minutes and it would

override the signal from the keypad or keyfob.

Set/unset Toggles the system status

SET,UNSET,SET,UNSET etc

12.41. Code/card reactions and section assignment

The following sequence programs the features of access codes

or cards:

62 nn r s

where: nn is the user position from 01 to 50

r is the reaction index from 0 to 9 – see Table 2

s is the section 1 = A, 2 = B, 3 = C (only has an

effect in a split system – except for the PG

output control reaction)

Guidance on assigning codes or cards to sections:

• In partial setting (arming) mode assigning codes or cards to sections

has no effect (except for the PG output control reaction). If anything in the

system is set and a card/code is used, the system will then be unset, and

if all sections are unset then the whole system will be set by a card/code.

Partial setting keys A and B on the keypad can be programmed to be

followed by a valid access code if required (see 12.13).

• For a split system, a code assigned to section:

A controls section A

B controls section B

C controls section A, B and C.

• If the system is not split then the assignment of codes/cards to

sections has no effect, but the s parameter must be entered in the

programming section. Enter s=3 if splitting is not desired.

Guidance on code/card reactions:

• If a code/card has a natural reaction, i.e. r=1, then its reaction is

set,unset,set etc. (the same as reaction r=9 in table 2).

• A code/card can also have an alarm reaction designated to it, similar

to detectors.

Factory default setting: all codes/cards from 01 to 50 have a

natural reaction (set/unset) and are assigned to section C.

12.42. Enrollment by keying in production codes

This sequence allow the enrollment of devices by keying in their

production codes:

60 nn xx..x

where: nn is the address of the device from 01 to 50

xx...x is the production code of the device (the last

eight digits of the bar code, see the label on

the PCB inside the device)

Notes:

• If the address nn is already occupied, the current device will be

erased, and the new device will then be enrolled instead.

• If a device with production code xx…x has already been enrolled to

another address in the past, and if the device is now enrolled to a new

address, then it will be moved to the new address, releasing the old

address.

• If you enter nn = 01 or 02, the device will enroll instead of the

corresponding hard-wired input in the control panel (the terminal will

be disabled).

• If eight zeros are entered as a production code, the device already

assigned to the address nn will be erased

12.43. Automatic setting/unsetting schedule

This can be used to program an automatic sequence of daily

setting/unsetting events. Up to 10 daily events can be

programmed. Events will occur every day of the week:

64 n a hh mm

where:

n is the event number from 0 to 9

a is the type of event from 0 to 6 (see the following

table)

hh hours (time of event)

mm minutes (time of event)

Erase the automatic schedule setting by : 64 n 0

* the same event in an unsplit system

** only possible if partial setting (arming) is programmed (see 12.24)

Notes:

• The automatic setting/unsetting event schedule can also be

programmed in maintenance mode.

• If automatic event scheduling is not used for setting/unsetting control

and the system is not split, then it can be programmed as a daily

timer to switch equipment connected to the PGY output on and off at

the desired daily times. To do this, split the system (see 12.24) but do

not enroll any detectors to section B (keeping this section empty).

Then program the PGY output to be triggered by the setting (arming)

of section B (see 12.5) and program the automatic daily event

schedule (with a=4) to set/unset the empty section B which will then

switch the PGY output on and off at the required times every day.

Factory default setting: All automatic events switched off.

12.44. Changing the service code.

To change the service code enter:

5 NC NC

where: NC = new code (4 digits), the new code has to be

entered twice

Example- the code 1276 can be programmed by entering: 5

1276 1276

Factory default setting: 8080

12.45. Go to maintenance mode

By entering 292 while in Service Mode the system switches to

maintenance mode. In maintenance mode it is possible to

program the devices to be bypassed and to adjust the control

panel internal clock (see 13.4).

12.46. Setting the internal clock

The control panel has a built in real-time clock which is used to

time-stamp all recorded events in the control panel memory.

Adjust the clock after installation by entering:

4 hh mm DD MM YY

where:

hh is the time in hours (00 to 23)

mm is the time in minutes (00 to 59)

DD is the day (01 to 31)

a Unsplit system Split system

0 No event No event

1 Set all (ABC) Set all (ABC)

2 Unset all (ABC) * Unset all (ABC)

3 Set A** Set A

4 Set AB** Set B

5 Unset all (ABC) * Unset A

6 Unset all (ABC) * Unset B

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80K in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80K

Jablotron JA-80K User Manual - English - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80K Manual

Product: