Manual Jablotron JA-80K (page 7 of 22) (English)

554835

Zoom out

Zoom in

1/22

Installation manual: Oasis security system JA-80K - 7 - MKE51801

control panel twice but to two different addresses with different

features –see 12.40.

• Only a single device can be enrolled to each address.

• When indicator A lights, it means the displayed address is

occupied and therefore no more devices can be enrolled to

this address.

• If a device has already been enrolled to an address, and it is

then re-enrolled to another address, the device’s address

assignment will change from the original address to the new

one.

• If a device cannot be enrolled to the control panel, either it

does not have a good wireless connection to the control panel

possibly due to excessive distance or it could be too close to

the control panel (closer than 2 meters is not permitted),

• To re-enroll a device, first disconnect its battery. Then wait

about 10 seconds or, to save time, press and release its

tamper switch to quickly discharge any remaining energy.

• A sub-control panel can be enrolled to a master control

panel by keying in the sequence 299 on the keypad of the sub

control panel which must be in Service mode. (see 12.10),

• If you intend to use final-door detectors in the system, they

must be enrolled to addresses 01 to 05 or 46 to 50 (see

12.23).

11.3. Testing enrolled devices

1. The control panel must have its antenna connected and be

in Service mode. If not in Service mode, then key in ∗0

service code (factory-default 8080). To enter Service mode

the control panel must be initially unset (disarmed).

2. Trigger the device to be tested (if it is a detector close its

cover first and then wait until it is ready for testing).

3. The keypad will beep and display a description of the signal

received from the device under test (the keypad cover

should be flipped open). We recommend technicians to

carry the wireless keypad around while testing to ease the

process.

Notes:

• Motion detectors JA-80P and JA-85P can be tested for a

maximum of 15 minutes after closing their covers. After this

period the detector will ignore frequent movements (see

detector manuals for details).

• Devices can also be tested in maintenance mode – see 13.4.

11.4. Measuring signal strength

1. The control panel must have its antenna connected and be

in Service Mode. If it is not, then enter ∗0 service code

(factory default: 8080). The control panel must be unset

(disarmed) to enter Service Mode.

2. Key in 298, and the lowest enrolled address will be

displayed.

3. Trigger the device enrolled to the displayed address. The

keypad display will show the received signal strength on a

scale of 1/4 to 4/4. Keep the keypad cover flipped open

while measuring signals.

4. Other addresses for devices can be selected using the

arrow keys to measure their signals too.

5. Exit signal measuring by pressing the # key.

Notes:

• Motion detectors JA-80P and JA-85P can be tested for a

maximum of 15 minutes after closing their covers. After this

period the detector will ignore frequent movements (see

detector manuals for details).

• Measuring the signals from a JA-80L internal siren can be

activated by pressing its button. A JA-80A outdoor siren can

be activated for signal strength measurement by opening its

cover thereby triggering its cover tamper switch.

• Each installed device should have a minimum signal strength

of 2/4. If the signal is too weak, the device should be relocated

or a higher control panel sensitivity can be selected. (see

12.36) Alternatively the control panel can be equipped with an

external antenna (see 10).

• This measurement shows the quality of the signal received

from the device at the control panel.

• The wireless keypad can be carried during installation or

testing by disabling its tamper contact via the jumper near the

tamper contact – do not forget to re-enable the tamper before

finishing the installation – Note: the keypad usually has a

slightly shorter working range than the detectors. Therefore, if

carried to more-distant detectors the triggering of the

detectors might not be shown.

• The most convenient way of measurement is via a computer

running ComLink SW.

11.5. Erasing enrolled devices

1. The control panel must be in Service Mode. If it is not, then

enter ∗0 service code (factory default: 8080). The control

panel must be unset (disarmed) to enter Service Mode.

2. Key in “1” to enter enrollment mode and using the arrow

keys select the desired address of the device you wish to

erase.

3. Press and hold the “2” key until a beep is heard and the A

indicator turns off.

4. After all the desired devices have been erased, press #.

Notes:

• To erase all wireless devices, press and hold the “4” key in

enrollment mode.

• If a wireless keypad is erased, it will stop communicating with

the control panel and must be re-enrolled before being used

again. (see 7.1).

11.6. Enrolling the control panel to UC and AC

modules

If you wish to use UC and AC modules to output PGX and PGY

signals, you must enroll the control panel to these modules as

follows:

1. The control panel must be in Service Mode. If it is not, then

enter ∗0 service code (factory default: 8080).

2. On the UC or AC module, enter the desired enrollment

mode (see the manual of the particular module)

3. Key in 299 on the control panel keypad and check that all

LEDs on the module flash a few times to confirm successful

enrollment.

Notes:

• Because the UC and AC modules have rather short

enrollment-period timeouts, we recommend locating the

module close to the control panel during enrollment.

Alternatively you could carry the wireless keypad close to the

module to perform enrollment.

• The control panel can be enrolled to the desired number of

UC/AC modules to control multiple PG outputs in an

installation.

• Each UC and AC module has 2 relays, X and Y which have to

go through enrollment separately. The X relay reacts to PGX

signals from an enrolled control panel and the Y relay reacts

to PGY signals from an enrolled control panel. The control

panel’s PGX signal can be enrolled to the X relay and the

control panel’s PGY signal can be enrolled to the Y relay.

Therefore, the enrollment procedure has to be done twice if

both relays are to be controlled by the control panel’s PG

signals.

• Only one control panel can be enrolled to a UC or AC receiver

because a control panel repeats its PG signals every 9

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80K in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80K

Jablotron JA-80K User Manual - English - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80K Manual

Product: