554835
4
Zoom out
Zoom in
Previous page
1/22
Next page
Installation manual: Oasis security system JA-80K - 4 - MKE51801
sent to alarm receiving centres (central monitoring stations).
They can notify the user using SMS reports and allow remote
control and programming of the system by mobile phone and
the Internet. Another option is the JA-80X communicator
which reports alarms via a traditional phone line using voice
messages.
Note: The Oasis JA-80 system has three modes: operating
mode, maintenance mode and service mode. Operating
mode is for the day-to-day use of the system by all authorised
users, e.g. setting/unsetting (arming/disarming). Maintenance
mode is for the holder of the master code (system administrator)
to have limited programming of the system, e.g. changing
codes/cards, bypassing and is inaccessible to all other users.
Service mode is only for installers and is used to program and
control all aspects of the system.
1.1. Optional system configurations
In the European Union region, follow the valid standards and
rules, especially series EN-501-xx. The Oasis control panel
complies with grade 2.
The control panel must have one of the following configurations
as a minimum:
At least two non-backup-battery sirens (JA-80L or SA-105) +
communicator class ATS2 (JA-80Y, JA-80V or JA-80X)
At least one backup-battery siren (JA-80A or OS-360/365/300)
+ communicator class ATS2 (JA-80Y, JA-80V or JA-80X)
No siren + communicator class ATS3 (JA-80Y or JA-80V)
Note: the above-recommended configurations are based on the
EU standard EN-50131-1 valid at the time of issuing this
manual.
2. Installation
The control panel can be attached to the wall using 3 screws.
The drilling template is on the last page of this manual.
Because the control panel communicates via radio, it
should not be installed near any large metal objects
capable of shielding radio communication.
Route cables (power supplies, telephone leads etc.) inside
the control panel before tightly screwing in the screws.
2.1. Power inlet
The control-panel power cable should only be installed by a
person holding a sufficient electro-technical qualification.
Mains fuse
T 200 mA
The control panel power supply is double-insulated (safety
class 2) and does not incorporate a protective earth wire.
A double-insulated power cable should be used with a
minimum cross-sectional area of 0.75 to 1.5 mm
2
. The
power cable should be connected to a switched mains
supply fused to 10 Amps.
In the control panel, connect the cable to the power
terminals equipped with a fuse of type T200mA/250V.
Fix the cable firmly to the cable holder in the control
panel making sure that the wire ends are properly secured
and connected in the terminals.
0
1
C
O
M
0
2
N
C
N
O
E
W
-
C
I
W
P
G
X
P
G
Y
G
N
D
A
B
+
U
A
C
2
0
V
antenna connector
RESET
Communicator
connector
Wiring plug
Digital bus
1A +U
fuse for
Termi n al s fo r
transformer output
Radio
module
memory socket
3. Control panel memory unit
The control panel memory unit plugs into its own socket. If, for
example, the control panel was damaged, the memory unit could
be unplugged and then plugged into another control panel circuit
board of the same type to transfer and preserve the settings
including enrolled detectors, access codes and cards. The new
control panel thereby becomes an exact copy of the former one
(a clone).
Notes:
There are no communicator settings in this memory unit
Do not connect or disconnect the memory unit while the control panel
is powered.
Although the memory unit is well-protected, in cases of severe
damage to the control panel there is a risk that memory contents
could be corrupted. It is therefore highly recommended to back-up the
settings in a PC using Comlink software.
4. Control panel connectors and terminals
Antenna connector – This is used to connect either to an
internal antenna or to external antennas such as the AN-80 or
AN-81.
Reset link (normally open) – Used to reset the control panel by
shorting the link only while powering up the control panel. This
link can also be used to enter control panel enrollment mode by
briefly shorting the link while the control panel is powered.
Digital bus connector – for connecting a JA-80E keypad or a
PC running Comlink software with a JA-80T interface cable. The
same digital bus connector is present on the bottom right hand
corner of the plastic housing. Additionally, the same connections
are available on the GND, A, B, +U terminals.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80K in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80K

Jablotron JA-80K User Manual - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info