554916
7
Zoom out
Zoom in
Previous page
1/12
Next page
MLO51201 - 18 -
System extension
Individually bought devices should be enrolled to Azor using a registration code. The code
consists of ten digits and it is in the following format: 123-4567-890. Enrollment (or removal)
of a device is performed with a computer. The registration code can be filled into the Serial
Number box on the Detectors page. If the registration code is unknown (e.g. damaged label)
please use A-Link. Choose the wanted field for enrolling the device and click the Enroll
button. Insert the battery into the device. As a confirmation of successfull enrollment the
registration code is displayed in the field.
AZ-10T RFID tag
There is a sticker with a registration code on a new RFID tag. If the RFID tag code is no
longer legible, please use the RFID tag reader and A-Link software for enrolling it. Choose
the Tag number field in the Users window and click the Enroll button. The code is enrolled
after pressing SET on the AT-10D RFID tag reader and scanning the RFID tag. As a
confirmation of successfull enrollment the registration code is displayed in the field.
Note: Azor uses special security RFID tags. No other RFID tags can be enrolled to it.
AZ-10M door-opening detector
Besides detecting door and window opening, the detector can also report e.g. the
movement of objects etc. You can also connect an external sensor to it.
Terminals:
INPUT serves for connecting external alarm sensors. When the GROUND terminal is
disconnected an alarm signal is sent (identical to that of reporting door
opening).
TAMPER serves for connecting external tamper sensors. When the GROUND terminal
is disconnected a tamper signal is sent (identical to that of reporting detector
opening).
GROUND common terminal. If the INPUT or TAMPER terminal is not used, it must be
permanently connected to this terminal.
Internal switches:
1 DEL the detector provides an entrance delay*
INST the detector does not provide an entrance delay*
2 MG EN the built-in magnetic sensor is enabled
MG DIS the built-in magnetic sensor is disabled (only INPUT terminal activation is
reported)
*) applies only if a “default” reaction is set for the detector
Battery-low signalling
When the detector batteries are low, Azor sends an informative message. Besides that the
detector LED flashes when you open the door (outside test mode).
MLO51201 - 7 -
Installation
First attach the detectors temporarily with double-sided adhesive tape. The screws can
only be used after the communication test. If the surface is smooth and cohesive, it is
possible to attach the detectors with only adhesive tape.
The distance between a detector and the GSM control unit must not exceed 20m.
Note: the radio signal can be blocked by metal objects, wet walls, and wall and ceiling
supporting structures, etc.
Door-opening detector installation
Attach the detector to a door frame (solid part); the antenna should point upward.
Attach the magnet to the door (if it is made of metal, use a plastic pad underneath).
When the door is closed, the magnet unit must almost touch the bottom part of the
detector (on the left or on the right).
Connect the batteries (leave the internal switches in the 1 DEL and 2 MG EN positions).
Close the detector (the tamper contact spring must be compressed).
When the door is opened, the detector indicator light should flash. You can test the
function for 5 minutes and then the indicator light goes off. You can repeat the test by
opening and closing the detector housing (a tamper activation).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron Azor GSM Mini at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron Azor GSM Mini in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron Azor GSM Mini

Jablotron Azor GSM Mini User Manual - English - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info