554916
11
Zoom out
Zoom in
Previous page
1/12
Next page
MLO51201 - 14 -
Control
The following description applies to Azor’s default settings. However, you can adjust its
behaviour as you wish – see the Settings.
A RFID tag reader is usually used to control Azor at the protected premises. Users whose
telephone has been enrolled to the system can also control Azor via the voice menu. The
access to the menu can be protected with a personal User’s code – see the Settings.
Switching Azor on/off
Azor can be switched on/off by holding the GSM control unit button. Azor reports its
switching on/off (to the ARC and also with an SMS message).
Setting Azor
Press the SET button on the RFID tag reader (A) and scan the RFID tag (B)
The red LED indicator in the reader lights up and a 1 minute exit delay is launched
Detector activation will not trigger an alarm in this time
Azor will confirm its setting with a longer beep
Tips and specifications
The system can also be set via the telephone voice menu.
A different exit delay can be set (see the Settings).
If you press the RFID tag reader button in a set state, a red LED indicator lights up.
When a detector is activated in the set state, an alarm is triggered. However, a 30 second
entry delay during which the user can unset the system is launched first (a different delay
can be set or it can be disabled for individual detectors – see Settings).
If there is any unauthorized manipulation of any part of the system in the set state, a tamper
alarm is triggered.
If the user has enabled SMS reporting when the system is set, no report is sent to them if
they set the system themselves by own remote control or RFID tag. An RFID tag marked by
a colour label on it is for the user whose phone number was enrolled as the first one. No
setting is reported when it is cancelled during the exit delay. This reduces unnecessary
SMS messages if you forget something when exiting the place and you have to return for it.
- 11 - MLO51201
Installation of the GSM control unit and its antenna
The GSM control unit should be installed in a concealed place. There must be
a mains socket for the connection of the supplied mains adaptor within reach.
If the LED indication on the front panel of the control unit is unwanted (may
show the place of unit installation) it is possible to switch it off using A-Link.
The LED indication is switched off within 15 minutes. If you need to check the
indication briefly press the button on the unit and the indication will appear for
15 minutes. In the case of power trouble the LED indication is always on.
No other electronic appliances should be near the GSM control unit (e.g. audio
systems, antenna cables) which may be influenced by the GSM transmitter in
the control unit.
You can use the template at the rear of the manual to mark the spots where
you want to fix Azor to the wall. The screws should protrude a bit so that the
electronic box can be put on the screw heads and secured by moving it
sideways.
Tamper detector
The GSM control unit has a sensitive tamper-switch at the bottom (a plastic
lever). Based on its activation by picking up the GSM control unit, the system sends
a tamper activation report to the user or ARC if enabled.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron Azor GSM Mini at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron Azor GSM Mini in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron Azor GSM Mini

Jablotron Azor GSM Mini User Manual - English - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info