555055
2
Zoom out
Zoom in
Previous page
1/4
Next page
AS-80 access system control unit MKM51600
2
If you have a JA-80N proximity reader, present the RFID card 10
times and when the reader performs a confirmation double-beep,
present the card 10 times again
5. After setting master or slave operation mode the reader will exit
setting automatically
6. Disconnect the power, re-connect the DTA terminal (brown) wire
and restore the power
Note: Further system programming can only be done on the master
keypad.
2. On the master keypad set the service and master card and/or code
as follows:
1. Disconnect the power
2. Disconnect the CLK terminal (Green wire) and connect it to the
yellow wire
3. Restore the power
4. After the reader starts sounding, disconnect the green and yellow wires
5. Choose master code or master card
a) Enter the new master code (3 to 6 digits) and press # # (only code)
b) Or press # and present the card (only card)
c) Or enter the new master code (3 to 6 digits) and press #,
present master card or press # again.
6. Choose service code or service card
a) Enter the new service code (3 to 6 digits) and press # # (only code)
b) Or press # and present the card (only card)
c) Or enter new service code (3 to 6 digits) and press #, present
the service card or press # again
7. Disconnect the power, connect the CLK (Green wire) wire back
and restore the power
Note: If the master or service code is forgotten or the card is lost, then by
this procedure it is possible to perform a factory default reset of the
keypad
The master and service code/card can only be used for programming
the system - it cannot be used for system operation.
Service mode
Enter service code or use the service card. The OPEN LED and
STATUS
LED light green (service mode).
To program any optional parameters always press all 13 digits C1 to
C13 according to following table. After entering the last digit the reader
saves all the data, and exits programming mode automatically.
Note: If you don’t press a key within 20 seconds, service mode will be
exited without saving any data.
Parameter Value Description Default
C1 and C2 00–99
C1 and C2 is a period of time during which the relay set as the Door lock is switched on (01 – 99 sec.). If 00 is
entered, then the output will be set to a latch mode (it toggles its status whenever a valid assigned code or card is
entered).
4 sec
C3 and C4 00
No meaning, enter 00
C5 0,4,6,7
RELAY 1 output reaction:
[0] – Off = no reaction
[4] – Door lock = switched on for a time specified in parameters C1-C2 when a correct code / card is entered
[6] – Tamper alarm = after 3 unsuccessful attempts at entering a code or card the output will produce a 4 second
long pulse
[7] – Door bell = whenever the F1 or F2 key on the keypad is pressed, the output will produce a 5 second long
pulse
Door lock
C6 0,4,6,7 RELAY 2 output reaction – setting parameters are the same as for RELAY 1
C7 0
No meaning, enter 0
C8 0 – 2
Function settings for IN:
[0] – Off = no reaction
[2] – Exit button switch = connecting IN to GND will have the same effect as entering a valid user code
Exit
button
switch
C9 0
No meaning, enter 0
C10 0 – 1
The access mode for the master keypad:
[0] - Card or Code
[1] - Card and Code
Card or
Code
C11 0 – 1
The access mode for the slave keypad / reader:
[0] - Card or Code
[1] - Card and Code
Card or
Code
C12 0 – 1
Tamper alarm indicated by an internal buzzer
[0] – Disabled
[1] – Enabled
Disabled
C13 0
No meaning, enter 0
Configuration parameters in service mode
Example: by entering 0200460200100 you will set – Door unlock time 2 seconds, RELAY1 reaction Door lock, RELAY2 reaction tamper alarm, IN
reaction exit button switch, master keypad access Card or Code, slave keypad access Card and Code, Alarm indicated by buzzer disabled.
Access code setting
120 different access codes and/or cards can be used. The factory
default codes are blank. All access codes can have from 3 to 6 digits.
Enter the master code or use the master card. The OPEN
LED and
STATUS
LED are lit (access code setting mode).
Setting access codes and RFID cards:
Use the sequence 3 ID CODE # Card
Where: ID is a user number (from 000 to 119)
CODE is a new code (3 to 6 digits), after pressing # present
the RFID card which will be assigned to the same
user position. If the card is not required, press the #
button again.
Deleting user codes and RFID cards:
Use the sequence 9 ID
Where: ID is a user number (from 000 to 119)
Delete all access code / cards
Use the sequence * 0
To exit, press the # key
Note:
- If you assign a new user code to an ID that is already occupied by
some other user, the original code will be deleted.
- Any attempt to program an already registered card or code will be
indicated as a programming error.
- If no button is pressed for 20 seconds the current sequence will be
terminated. If no button is pressed for 150 seconds then setting mode
will be exited.
Operation
By entering a proper access code followed by the # key and/or
presenting an RFID card, the output set as Door lock will be switched
on for a set period of time (confirmed by 3 short beeps). If the latch
mode has been set, then every proper code entry will toggle the status of
the output – ON-OFF-ON-.
Whether the RFID card must be followed by the code or not can be set
separately for master and slave keypads. Therefore, for example, for a
higher level of security, to enter the premises both a card and code could
be required, and to leave the premises only a card or code could be
required.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron AS-80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron AS-80 in the language / languages: English as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info