Manual Jablotron AC-88 (page 1 of 2) (English)

554861

Zoom out

Zoom in

1/2

AC-88 smart wireless socket 1/2 MZZ55400

AC-88 smart wireless socket

The AC-88 wireless socket is a component of Jablotron‘s JA-8x

series OASiS systems. It contains one independent, wirelessly

controlled power relay. The device is mains-powered and it can be

used as:

• a remotely-controlled appliance switch (max. 230V/ 50Hz/ 16A)

• a wireless switch for electric heaters and boilers

• an automatic wireless switch for appliances in “standby“ mode

• a wireless controller for lighting, ventilation, etc.

It is ideal for use in home automation in flats where construction work

would be undesirable. The AC-88 can be controlled with:

• a built-in button on the socket,

• RC-8x OASiS wireless remote controls,

• JA-8x OASiS wireless detectors,

• TP-8x OASiS wireless thermostats,

• wireless PG output control signals:

o from JA-8xK OASiS alarm control panels,

o from GD-04 DAViD GSM controllers and diallers,

o from EYE-02 security cameras.

Warning: The switch is intended to single pole switching, does not

ensure safety disconnection

Installation

The wireless socket is installed by plugging it into a mains socket

(230V) which can be done by the user. The button on the wireless

socket is used to set its properties and to switch the connected

appliance on/off. The LED indicator under the button shows active

status of the socket. Up to 8 transmitters using Jablotron OASiS

protocol can be enrolled to the socket to switch the connected

appliance on/off or switch it on for a set period of time. When the

appliance is switched on/off, the socket also transmits status change

information to other devices or sockets.

Programming mode selection

Firstly enrol the control devices in the desired mode and set the timer if

desired according to the table below.

Plug the socket into the mains. The LED indicator will flash for a short

moment. Press the button on the socket within 10 seconds after plugging in

(the LED indicator will flash once) and hold it until the LED indicator starts

flashing repeatedly once per second. When you release the button while

the indicator is flashing once per second, you enter the 1

enrolment mode

– switching on. If you hold the button for five more seconds without

releasing, the LED starts flashing twice per second and you can release the

button to enter 2

enrolment mode – switching off. If you hold it for five

more seconds, the flashing frequency changes to three flashes per second

and releasing the button triggers timer setting mode. When the button is

released when there are four flashes per second, you enter reset mode.

Switch-on mode

Open the 1

(switch-on) enrolment mode and enroll desired transmitters:

o a remote control

• By pressing any button – when you exit enrollment mode the

enrolled button can be used to switch the socket on/off.

• By pressing the + or + buttons simultaneously – when

you exit enrollment mode, the socket will only react to simultaneous

pressing the

+ or + buttons. Pressing these buttons

activates the socket for a period of time which has been set on the

timer (default setting is 2 minutes), see “Timer Use“.

• By simultaneously pressing the + or + buttons for about

5 seconds (confirmed by three quick flashes of the LED indicator

on the remote control) – pressing

activates the socket

while pressing

or deactivates it. Simultaneous pressing of

both buttons (

+ or + ) activates the socket for a period of

time set on the timer (default setting is 2 minutes).

Sending Panic signal from controllers (RC-87, RC-89, RC-86, etc) will

result in socket activation for a period of time set on the timer (default

setting is 2min).

o a detector / thermostat – by inserting a battery into the device. In

normal operation the socket copies the detector / thermostat status –

activation of the device switches the appliance plugged into the socket

on and deactivation of the device switches the appliance off. Impulse

reaction detectors (e.g. JA-80P, JA-85P, JA-8xM detectors with

adjustable impulse reaction, etc.) activate the socket for a period of time

set on the timer (default setting is 2 minutes),

o PGX control panel output – by keying in 299 on the OASiS keypad in

service mode – the socket copies the status of the control panel’s PGX

output,

o PGY control panel output – by keying in 299 on the OASiS keypad in

service mode twice in a row – the socket copies the status of the control

panel’s PGY output,

o GD-04 communicator – by pressing the XY button on the GD-04R

radio module once – the socket copies the status of the X relay in the

communicator, by pressing the XY button on the GD-04R radio module

twice - the socket will copy the status of the Y relay,

o another AC-88 socket – by plugging in another AC-88 socket to an

mains (230V) – the original AC-88 socket copies the second AC-88

• Enrolment of each transmitter is confirmed by a long flash of the

LED on the socket.

• The socket will exit the enrollment mode automatically if no enrolment

signal is received within 5 minutes after entering the enrollment mode

or by pressing the socket button briefly (the flashing will stop).

Notes:

• If you want to enrol a detector which has already been connected to a battery, first

disconnect the battery, then press the tamper contact in the cover several times to

discharged the capacitors and then start the enrolment.

• If device enrollment fails, the device is either too far from the receiver or 8 devices

have been already enrolled..

• Devices can be enrolled during multiple enrollment cycles.

• If the same device is enrolled repeatedly, the socket will react according to the

latest setting.

• Each transmitter (remote control, detector, control panel, etc) can be enrolled to

more receivers.

• The socket always follows the latest command (e.g. if it is switched on permanently

by a button and then receives a command to switch on for 2 minutes, it remains

active for 2 minutes and then switches off).

• All devices are enrolled into non-volatile memory and remain saved when the

socket is unplugged from the mains or when enrollment mode is entered

repeatedly.

• Detailed information about device enrollment is available in its installation manual.

• When the power supply is restored after a power failure, the socket remains

switched off due to safety reasons until any valid signal is received.

# Indication Mode Notes

1 flash per

sec.

Switch on

(normal)

• Status devices (JA-81M, RC-86) switch

the socket on when activated and off when

deactivated.

• Impulse devices (e.g. JA-80P) switch the

socket on for a time set on the timer.

• The socket copies status of the control

panel’s PG output.

2 flashes

per sec.

Switch off

(inverse)

• Status devices switch the socket off when

activated.

• The inverse mode should not be used for

periodically transmitting impulse devices

• The PG output triggers an opposite

reaction in the socket (triggering PG

causes the socket to switch off).

3 flashes

per sec.

Timer

setting

• You can set activation time from 1 minute

to 24 hours. One second set during setting

corresponds to 1minute in the real

operation time, see Timer Use chapter

(default setting is 2 minutes)

4 flashes

per sec.

Reset

• Erases all enrolled devices and sets the

timer to default settings, see Device reset

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron AC-88 in the language / languages: English as an attachment in your email.

The manual is 0,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron AC-88 Manual

Product: