686578
32
Zoom out
Zoom in
Previous page
1/34
Next page
344
NLA
S AVE THESE INSTRUCTIONS
(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019
English
Page 32
TROUBLESHOOTING (continued)
LED PANEL
CODE PROBLEM SOLUTION
LED Panel Code Flash & Alarm On (NOTE: Always turn off the power before cleaning and servicing).
E81
Transmission signal failure.
Reset the RCD, restart all over again.
Place the control panel within 5 m (16 ft) of the control base unit.
Press and hold POWER button for 5 seconds to turn off and charge the
panel again.
If problem persists, contact Intex Service Center.
E90
No water ow.
Turn off and unplug the control unit.
Ensure the outlet cover grid is clean and free from obstructions.
Clean or replace the cartridge, see Maintenance and Storage section.
Ensure the in/outlet connections on the spa tub and lter pump are not blocked.
Keep the spa water properly sanitized to ensure a clean and unclogged lter
cartridge.
If problem persists, contact Intex Service Center.
E91
Dirt or scale on titanium plates.
Low salt level / No salt.
Electrolytic cell cord is loose.
Possible electrolytic cell failure.
Remove the electrolytic cell for inspection. Clean it if necessary. See
“Maintenance”.
Add salt. See “Salt Level Information”.
Ensure that the cell cord is plugged rmly into the cell receptacle.
Contact Intex Service Center. Replace the cell if needed.
E92 High salt level.
Partially drain the pool and re ll it with fresh water. See “Salt Level Information”.
If problem persists, contact Intex Service Center.
E94
Water temperature too low.
If the ambient temperature is below 4°C (39°F), we recommend not to use
the spa.
Turn off and unplug the control unit, add some warm water to raise the
spa water temperature above 5°C (41°F), then press the button to
heat up the water to the desired temperature.
If problem persists, contact Intex Service Center.
E95
Water temperature is
around 50°C (122°F).
Turn off and unplug the control unit. When the water has cooled down,
plug the RCD and restart all over again.
Turn the heater off, then press the lter and jet buttons to lower the water
temperature.
If problem persists, contact Intex Service Center.
E96 System Error.
Turn off and unplug the control unit. Plug the RCD and restart all over again.
If problem persists, contact Intex Service Center.
E97 Dry- re Protection.
Contact Intex Service Center.
E99
Water temperature sensor broken.
Contact Intex Service Center.
END
After 72 hours of continuous
heating operation, the pump
will hibernate automatically.
The rapid heating and water
ltration functions are disabled.
Press the button to re-active the lter pump.
NO LED
DISPLAY
LED display is off
Charging Failed
Control Panel failure.
Press any button to reactivate the control panel.
Reset the RCD, restart all over again and charge the control panel again.
Make sure the surface between the back of the control panel and the
control base recessed channel is clean, dry and free of obstruction.
If problem persists, contact Intex Service Center.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex PureSpa - 28492 PS-BH-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex PureSpa - 28492 PS-BH-20 in the language / languages: English as an attachment in your email.

The manual is 5,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex PureSpa - 28492 PS-BH-20

Intex PureSpa - 28492 PS-BH-20 User Manual - German - 34 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - Dutch - 25 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info