Manual Ignis AKS 101 (page 2 of 4) (English)

611556

Zoom out

Zoom in

1/4

The cooktop should not be forced into the

worktop. Forcing the glass-ceramic top may cause

it to crack (even at a later date)!

• If the worktop is made of wood

, use the spring

clips and screws provided (Fig. 7).

Secure the spring clips (D) (Fig. 7) with the

screws provided (E) (Fig. 7) as shown, paying

attention to the specified distances.

Fit the cooktop into the worktop.

• If the worktop is made of marble, plastic,

ceramic, stone, etc.

, the cooktop must be

secured with special brackets (F) (Fig. 7), Code

4819 404 78697 available at After Sales Service.

Fit the cooktop into the worktop.

Place the 4 brackets (F) in position in

accordance with the thickness of the worktop

as shown in Fig. 8.

Fasten the 4 screws (G) in the positions (H)

(Fig. 8).

Electrical connection

Regulations require that the appliance be

earthed.

•

Connection to the mains must be carried out by

a qualified technician in accordance with the

manufacturer’s instructions and in compliance

with local regulations.

•

The installer is responsible for connecting

appliances correctly to the mains and for

observing the safety regulations.

•

The oven power cable must be long enough to

connect the built-in appliance to the mains.

•

Observance of safety directives requires that a

multi-pole switch with a minimum contact gap of

3mm be used for the installation.

•

Do not use multiple plug adapters or extension

leads.

•

After the oven has been installed, the electrical

components must be inaccessible.

Connecting the oven to the power

supply

•

Make sure that the voltage indicated on the rating

plate is the same as the mains voltage. The rating

plate is on the front edge of the oven (visible

when the door is open).

Remove the two fastening screws of the

terminal box cover located on the bottom part

of the oven’s rear covering.

Remove the cover to gain access to the terminal

box and insert the power cable (see table)

through the opening located on the bottom of

the oven.

Connect the cable to the terminal box, tighten

the screws as far as they will go and secure it to

the cable fastener.

Put the cover back on by inserting the two blades

in the slots and fasten it with the two screws.

Interconnecting cooktop and oven

Important: do not connect the oven to the

power supply before you have finished

connecting the oven and cooktop.

•

Before connecting the oven to the power supply,

make sure that the cooktop is among the ones

listed in the cooktop/oven pairing product sheet

provided.

•

Remove the cover (L) (Fig. 9) (if present) of the

connectors (D) (Fig.9) located on the top covering

of the oven by loosening the fastening screw (M)

(Fig. 9). Lift up the cover (L) to gain access to the

connectors (D) and connect the connectors of the

cooktop (C) (Fig. 9) to the connectors of the oven

(D), matching the colours and alignment of the

housing guides visible on top of the connectors.

•

Then make the connection by pushing the

connectors all the way in, making sure that the

tongue clicks into place. Put the cover (L) back and

let the cables stick out from the bottom. Fasten

the cover with the screw removed previously.

•

Unscrew the nut of the ground screw (K) (Fig. 9)

on the top covering of the oven and insert

the yellow/green ground cable, leaving the

washer in place. Screw the nut back onto the

screw and tighten it as far as it will go.

Important:

If the cooktop terminals do not

correspond to the connection and colour

indications on the cooktop/oven connection plate

located at the top of the oven, request the adaptor

kit, code

AMC 873

, from the After-sales Service.

Securing the oven

•

Lift up the oven getting hold of it by the openings on

the sides and insert it into the housing unit, being

careful not to trap the power supply cable (Fig.10).

•

Center the oven in the housing unit before

securing it.

•

Make sure that the plastic spacers (if provided)

are positioned correctly in the fastening holes.

Then anchor the oven to the housing unit with

the screws provided.

Power supply cable table

N° of conductors Type of cable

1N+

H05 RR-F 3 X 4 mm²

2N+

H05 RR-F 4 X 2.5 mm²

3N+

H05 RR-F 5 X 1.5 mm²

H05 RR-F 4 X 2.5 mm²

10200157aGB.fm Page 4 Monday, September 5, 2005 3:53 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ignis AKS 101 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis AKS 101

Ignis AKS 101 User Manual - English - 8 pages

Ignis AKS 101 Installation Guide - German - 4 pages

Ignis AKS 101 User Manual - German - 8 pages

Ignis AKS 101 Installation Guide - Dutch - 4 pages

Ignis AKS 101 User Manual - Dutch - 8 pages

Ignis AKS 101 Installation Guide - French - 4 pages

Ignis AKS 101 User Manual - French - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ignis AKS 101 Manual

Product: