611556
1
Zoom out
Zoom in
Previous page
1/4
Next page
3
INSTALLING THE UNDER THE COUNTER
OVEN
Recommendations
Important: Disconnect the oven from the mains
before carrying out any installation work or
servicing.
Installation must be carried out by a qualified
technician in accordance with the manufacturer’s
instructions and in compliance with local
regulations.
Unpack the oven and make sure that the
appliance has not been damaged during transport
and that the oven door closes properly.
If you
are not sure contact the dealer or the
nearest service centre.
After removing the oven from its packaging,
leave it on the polystyrene base to prevent it
from being damaged.
When installing the oven it is advisable to wear
protective gloves.
Do not lift the oven by the door handle. Get hold
of it using the side openings provided.
Preparing the housing unit
Built-under oven
Kitchen units in contact with the oven must be
heat resistant (80 °C min).
Cut the kitchen unit and worktop to fit before
installing the appliances. Carefully remove any
shavings or sawdust that could prevent the
appliances from running properly.
The dimensions of the oven and unit are shown
in figures 1-2-3.
To allow for proper ventilation, an opening
should be left at the bottom of the housing unit.
Pay attention to the dimensions in Fig. 3.
Leave a minimum clearance of 5 mm between
the upper edge of the oven and the lower edge
of the worktop.
This clearance must never be
obstructed (Fig.2).
Make sure that the sides of the oven do not touch
the adjacent units.
If the kitchen unit is not securely fixed to the wall,
it must be anchored with standard brackets (G)
available on the market, see Fig. 3.
Cooktop
Caution:
to install the cooktop on surfaces other
than wood (e.g. plastic, ceramic, marble, stone,
etc.) remember to ask After Sales Service for the
fixing plates (Fig. 6-8).
The cooktop must be fitted in a worktop with a
minimum thickness of 20 mm and a maximum of
50 mm.
There must be nothing between the cooktop and
the oven (e.g. cables, insulating material, etc.).
An adjacent column unit must be installed at least
100 mm from the edge of the cooktop (Fig. 4).
Cut an opening in the worktop of the dimensions
given in the Product Description Sheet supplied
with the worktop.
We recommend you seal the internal edges of
the worktop with wood glue or silicone.
If not already in place, apply the supplied seal to
the cooktop, after cleaning the adhesive surface
thoroughly.
Conventional electric cooktop
Important: remove any protective film before
installing the cooktop.
If the worktop is made of wood, use the
spring clips and screws provided.
1.
Insert the 4 spring clips (B) (Fig. 5) in their
guides on the bottom of the cooktop.
2.
Fit the cooktop into the worktop.
If the worktop is made of marble or other
material (e.g. plastic, ceramic, marble, stone,
etc.)
, the cooktop must be secured with special
brackets (C) (Fig. 6), Code 4819 310 18528,
available from After Sales Service.
1.
Fasten the brackets into the holes with the
screws provided.
2.
Fit the cooktop into the worktop.
Glass-ceramic cooktop
Important: Remove any protective film before
installing the cooktop.
Make sure that that the opening in the worktop for
the cooktop is cut according to the dimensions
given in the drawing on the Product Description
Sheet. Pay attention to the tolerance range.
10200157aGB.fm Page 3 Monday, September 5, 2005 3:53 PM
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ignis AKS 101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ignis AKS 101 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis AKS 101

Ignis AKS 101 User Manual - English - 8 pages

Ignis AKS 101 Installation Guide - German - 4 pages

Ignis AKS 101 User Manual - German - 8 pages

Ignis AKS 101 User Manual - German - 8 pages

Ignis AKS 101 Installation Guide - Dutch - 4 pages

Ignis AKS 101 User Manual - Dutch - 8 pages

Ignis AKS 101 Installation Guide - French - 4 pages

Ignis AKS 101 User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info