621959
85
Zoom out
Zoom in
Previous page
1/111
Next page
86 • OWNER’S MANUAL
should be on the outside, between the fork blade and
the axle nut. If your bike has a clip-on type secondary
retention device, engage it. While pushing the wheel
firmly to the top of the slots in the fork dropouts, and
at the same time centering the wheel rim in the fork,
use the correct size wrench to tighten the axle nuts
enough so that the wheel stays in place; then use a
wrench on each side to tighten the nuts very tightly.
Re-engage the brake quick-release mechanism to
restore correct brake pad-to-rim clearance; spin
the wheel to make sure that it is centered in the
frame and clears the brake pads; then pull the brake
lever and make sure that the brakes are operating
correctly.
Removing a Bolt-On Rear Wheel
If your bike is equipped with an internal gear rear
hub, do not attempt to remove the rear wheel. The
removal and re-installation of internal gear hubs
require special knowledge. Incorrect removal or
assembly can result in hub failure, which can cause
you to lose control and fall. Furthermore, such hubs
are quite expensive to service & replace.
Shift the rear derailleur to the smallest, outer rear
sprocket; this is the high gear position. If your bike
has rim brakes, disengage the brake’s quick-release
mechanism to increase the clearance between the
rim and the brake pads. Using a correct size wrench,
loosen the two axle nuts.
Lift the rear wheel a few cm above the ground and,
with the derailleur body pulled back, push the rear
wheel forward and down until it comes out of the
frame rear dropouts.
Installing a Rear Bolt-On Wheel
Make sure the rear derailleur is still to the high gear
position. Pull the derailleur body back with your
right hand and put the chain on top of the smallest
sprocket, insert the wheel into the frame rear
dropouts and pull the wheel tight all the way back
and into the dropouts. The axle nut washers should
be on the outside, between the frame and the axle
nut. Using the correct size wrench, tighten the axle
nuts enough so that the wheel stays in place; then
use a wrench on each side to tighten the nuts very
tightly.
Re-engage the brake quick-release mechanism to
restore correct brake pad-to-rim clearance; spin the
wheel to make sure that it is centered in the frame
and clears the brake pads; then press the brake lever
and make sure that the rear brakes are operating
correctly.
Seat Post Quick Release
Most bicycles nowadays are equipped with a quick
release seat post clamp.
85

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ideal Jump up at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ideal Jump up in the language / languages: English, German as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info