627061
4
Zoom out
Zoom in
Previous page
1/76
Next page
4
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED CHANG E S AND T YPI N G ERRORS RESERVED
2. addiTional safeTy rUles
Always keep in mind that:
the machine must be switched off and disconnected from the power supply during maintenance and repairs,
clamped workpieces may only be measured when the machine is switched off.
Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap.
Do not remove safety devices or guards. Never use the machine while a guard is open.
Always use safety glasses for machining rough materials.
Burrs and chips should only be removed using a sweeper or other aid, never with your bare hands!
Never leave the machine running unattended.
3. characTerisTics and applicaTions
Swing over bed 410 mm
Swing over cross slide 255 mm
Swing in gap 580 mm
Distance between centers 1000 mm
Center height 205 mm
Width of bed 250 mm
Speed range I 30-550 RPM
Speed range II 550-3000 RPM
Threadcutting (metrisch) 0.2-14 mm
Threadcutting (Whitworth) 2-72 TPI
Longitudinal feed range 0.05-1.7 mm/p.r.
Cross feed range 0.025-0.85 mm/p.r
Threadcutting (module) 0.33.5 MP
Threadcutting (pitch) 8 - 44 DP
Nonius longitudinal feed 0.2 mm 1-omw = 19.6 mm
Nonius cross feed 0.02 mm 1-omw = 5 mm
Nonius tool holder 0.02 mm 1-omw = 2.5mm
Nonius tailstock 0.02 mm 1-omw = 2.5mm
Diameter tailstock 50 mm
Taper tailstock MT4
Taper of spindle internal-external MT6, D1-6 Camlock
Hole through spindle 52 mm
Tailstock spindle travel 120 mm
Cross slide travel 210 mm
Top slide travel 140 mm
Main motor power 5.5 kW 400V 50Hz
Coolant pump 90W 400V 50Hz
Coolant pump capacity 20 ltr/min
Weight 1550 kg
Subject to change.
4. insTrUcTions for UsinG This Machine
Read the safety rules carefully and always observe them. Examine the applications of this machine and beware of
possible risks.
Always wear safety glasses!
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 410 X 1000 VAC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 410 X 1000 VAC in the language / languages: English as an attachment in your email.

The manual is 4,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 410 X 1000 VAC

Huvema HU 410 X 1000 VAC User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info