477593
38
Zoom out
Zoom in
Previous page
1/68
Next page
38
IMPORTANT! COLD STARTING FOR HYDRO
COLD STARTING FOR HYDRO (BELOW 40°F[4°C]) - AF-
TER STARTING ENGINE AND BEFORE DRIVING, LET
TRANSMISSION WARM UP FOR ONE (1) MINUTE BY
PLACING MOTION CONTROL LEVER IN NEUTRAL (N)
POSITION AND RELEASING CLUTCH/BRAKE PEDAL.
WICHTIG! KALTSTARTEN FÜR MASCHINEN MIT
HYDROSTATISCHEM GETRIEBE
FÜR TEMPERATUREN UNTERHALB VON 40° (4°C).
NACH DEM ANLASSEN DES MOTORS DAS GETRIEBE
(1) MINUTE LANG AUFWÄRMEN LASSEN, BEVOR
LOSGEFAHREN WIRD. HIERZU DAS SCHALTGETRIEBE
IN.
ATTENTION! DÉMARRAGE FROID POUR UNE
HYDROSTATIQUE
POUR LES TEMPÉRATURES AU-DESSOUS DE 40°F/
4,44°C: APRÈS DÉMARRER LE MOTEUR ET AVANT DE
CONDUIRE, LA TRANSMISSION DOIT SE RECHAUFFER
PENDANT UNE (1) MINUTE EN D´EPLAÇANT LE LEVIER
DU CHANGEMENT DE VITESSE À LA POSITION POINT
MORT ET EN RELÂCHANT LA PÉDALE DE FREIN/
EMBRAYAGE.
IMORTANTE! EMPIESO EN FRÍO PARA HIDROSTÁTICO
PARA TEMPERATURA MENOR QUE 40°F (4°C).
DESPUÉS DE HABER EMPESADO EL MOTOR Y ANTÉS
DE CONDUCIR, DEJE QUE LA TRASMICIÓN SE CALIENTE
DURANTE (1) MINUTO PONIENDO EL DISPOSITIVO DE
CAMBIO A NEUTRO (N) Y SOLTANDO EL PEDAL DEL
EMBRAGUE/FRENO.
ATTENZIONE! AVVIAMENTO A FREDDO PER
TRASMISSION!
PER TEMPERATURE INFERIORI AL 40°F (4°C). DOPP
AVER AVVIATO IL MOTORE, E PRIMA DI METTERLO IN
AVANZAMENTO, LASCIARE RISCALDARE IL GRUPPO
TRASMISSIONE PER UN (1) MINUTO METTENDO IL
CAMBIO IN FOLLE E DISINNESTANDO IL PEDALE DEL
FRENO/FRIZIONE.
BELANGRIJK! LOUD STARTEN VOOR HYDRO
VOOR TEMPERATUREN ONDER 40°F (4°C). NA HET
TARTEN VAN DE MOTOR EN VÓÓR HET RIJDEN DE
TRANSMISSIE (1) MINUUT WARM LATEN LOPEN DOOR
DE VERSNELLINGSHENDEL IN NEUTRAAL TE
PLAATSEN EN HET REM/KOPPELINGSPEDAAL LOS TE
LATEN.
PURGE TRANSMISSION
To ensure proper operation and performance, it is recom-
mended that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have devel-
oped during shipping of your tractor.
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REIN STALLATION BEFORE OPER-
ATING THE TRACTOR.
Park tractor on level surface so it will not roll in any
direction. Parking brake must be disengaged for the
following procedure.
Disengage transmission by placing freewheel control in
freewheeling position.
Start engine and move throttle control to slow position. Be
sure parking brake is not engaged.
Move motion control lever to full forward position and
hold for five (5) seconds. Move lever to full reverse
position and hold for five (5) seconds. Repeat this
procedure three (3) times.
Move motion control lever to neutral (N) position.
Stop tractor by turning ignition key to "OFF" position.
Engage transmission by placing freewheel control in
driving position.
Start engine and move throttle control to slow position.
Drive tractor forward for approximately five feet then
backwards for five feet. Repeat this driving procedure
three times.
Your tractor is now ready for normal operation.
ENTLÜFTEN DES GETRIEBES
Um vorschriftsmäßigen Betrieb und einwandfreie
Leistungsfähigkeit des Getriebes zu gewährleisten, sollte
dieses vor der ersten Inbetriebnahme des Traktors entlüftet
werden. Auf diese Weise wird sichergestellt, daß sämtliche
Luftblasen, die sich während des Transports des Traktors im
Getriebe gebildet haben könnten, entfernt werden.
WICHTIG: FALLS DAS GETRIEBE FÜR ETWAIGE
WARTUNGSARBEITEN ODER ZUM ERSATZ AUSGEBAUT
WERDEN MUSS, SOLLTE ES NACH DEM WIEDEREINBAU
IM TRAKTOR ENTLÜFTET WERDEN, BEVOR DIESER IN
BETRIEB GENOMMEN WIRD.
Den Traktor auf ebenem Boden abstellen und
sicherstellen, daß er nicht ins Rollen kommen kann. Für
diesen Vorgang kann die Feststellbremse nicht eingelegt
werden.
Das Getriebe auskuppeln, indem die Freilauf-Schaltung
auf Freilauf geschaltet wird.
Den Motor anlassen und die Gasbedienung auf
langsamen Leerlauf stellen. Sicherstellen, daß die
Feststellbremse nicht eingelegt ist.
Den Gangschalthebel ganz in die Vorwärtsstellung
rücken und fünf (5) Sekunden festhalten. Dann den
Hebel ganz in die Rückwärtsstellung rücken und ebenfalls
fünf (5) Sekunden lang festhalten. Dieses Verfahren
dreimal (3) wiederholen.
Den Gangschalthebel auf die Neutral-Stellung (N)
rücken.
Den Traktor abstellen, indem der Zündschlüssel in die
“AUS” (OFF) Stellung gedreht wird.
Die Freilauf-Schaltung in die Fahrtstellung rücken, um
das Getriebe einzukuppeln.
Den Motor anlassen und die Gasbedienung auf
langsamen Leerlauf stellen.
Den Traktor etwa 1,50 m (5 ft) weit nach vorne fahren und
dann um etwa 1,50 m (5 ft) zurücksetzen. Dieses Verfahren
dreimal wiederholen.
Der Traktor ist jetzt normal betriebsbereit.
PURGER LA TRANSMISSION
Pour assurer l’utilisation correcte et le rendement, il est
recommandé que la transmission soit purgée avant d’utiliser
le tracteur pour la première fois. Ce procédé enlèvera l’air
emprisonné à l’intérieur de la transmission qui se
développerait pendant l’expédition de votre tracteur.
ATTENTION: SI VOTRE TRANSMISSION DEMANDE
L’ENLÈVEMENT POUR L’ENTRETIEN OU LE
REMPLACEMENT, ELLE DEVRAIT ÊTRE PURGÉE APRÈS LA
RÉINSTALLATION ET AVANT D’UTILISER LE TRACTEUR.
55
55
5
Eng
F
Esp
NL
Eng
F
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna YTH200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna YTH200 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info