Manual Husqvarna CTH194 (page 25 of 100) (English, German, Dutch, French, Italian, Spanish)

477562

Zoom out

Zoom in

1/100

• Once bagger assembly is in proper position, tighten adjust-

ment bolts (2) on both sides to 100 In-Lbs/11,2 Nm. Do NOT

overtighten.

• Readjust if necessary.

VERTICAL ADJUSTMENT

If necessary, the vertical position of the bagger assembly can be

adjusted to maintain proper alignment (B) between the fender

and the bagger assembly top.

• Replace bagger assembly onto bagger supports (5).

• Readjust if necessary.

• Remove bagger assembly.

• Do NOT remove; only loosen nuts (3).

NOTE: The bagger height indication marks (4) can be used to

help determine how much the bagger supports (5) will need to

be moved.

• Raise or lower bagger supports (5) to proper position and

retighten nuts (3).

TO ADJUST BAGGER

HORIZONTAL ADJUSTMENT

The tractor comes from the factory with the bagger assembly preset

in a fixed position. If necessary, this position can be adjusted to

maintain a consistent gap (A) between the fender and the bag-

ger assembly top. An ideal gap is approximately 0.25” (6 mm).

• Insert 1/2" (13mm) wrench under bagger assembly top (1).

Do NOT remove; only loosen adjustment bolt (2). Repeat on

opposite side.

• Slide bagger assembly into proper position.

TO INSTALL BAGGER FULL LEVER/EXTENSION

Before installation or adjusting, tractor engine must be shut off

and parking brake engaged.

• Remove center discharge chute. (See "To Remove Center

Chute" in section 6 of this manual.)

• Remove bolt (1). Place lever (2) into slot and reinstall bolt

(1). Adjust as needed.

TO ADJUST BAGGER FULL LEVER/EXTENSION

Slide bagger full extension (3) to the desired position.

• For the heaviest/wet grasses, slide extension all the way in.

• For the lightest/driest grasses, pull extension all the way out.

TO INSTALL BAGGER SPRING LATCH

The bagger spring latches are located on the back plate (1),

one in each of the bottom corners.

Before installing, tractor engine must be shut off and parking

brake engaged.

• Install each bagger spring latch with the loop end (2) down

and facing towards the bagger assembly.

• Place the mounting bolt (3) through the backplate. Place

curved end of the bagger spring latch onto mounting bolt (3)

and secure with nut (4) as shown. Tighten firmly.

NOTE: The bottom of the bagger assembly should contact the

loop end so that it is held securely when closed.

NOTE: If the bagger assembly height is adjusted, it may be

necessary to adjust the bagger spring latch. To adjust, remove

the nut (4) and move the bagger spring latch to the appropriate

hole in the backplate (1), ensuring the bagger assembly will be

securely closed. Retighten nut securely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH194 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 10,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna CTH194 Manual

Product: