477562
24
Zoom out
Zoom in
Previous page
1/100
Next page
24
2
TO ASSEMBLE BAGGER
Unfold bag and stand right side up.
Uninstall carriage bolts (5/16-18 x 1.5) and nuts (1) from the
front of the top frame.
Snap bottom of front bagger frame (3) into snap feature at
front of bagger bottom.
Remove cross braces (4) from inside of bagger assembly.
Slide cross brace (4) onto pin (5) at the rear of the upper
bagger frame and secure with retainer spring clip (6).
Slide cross brace (4) onto pin (7) at the front of the bagger
frame and secure with retainer spring clip (8).
Repeat on opposite side.
TO INSTALL BAGGER SUPPORT ASSEMBLY
Using a T30 Torx socket, loosen set screw (1). Remove
clevis pin (2) and spring clip (3).
NOTE: Set screw (1) should be loosened first and then upon
reinstallation of bagger support assembly, tightened down last.
Slide bagger support mount (4) off of bagger support tube
(5).
Repeat these steps for both bagger support assemblies.
Remove clevis pin (9) and retainer spring (10) from bagger
handle (11).
Slide bagger handle (11) down through bagger cover and
frame holes.
Reinstall clevis pin (9) through hole at bottom of bagger
handle (11) and slide retainer spring (10) into hole at the end
of the clevis pin (9) until it locks into place.
Feed front bagger frame (2) up through fabric loops at each
side of bagger.
Reinstall carriage bolts and nuts (1) to connect front frame to
top frame, passing through bagger.
Remove the mounting bolts (6) from the back of the unit.
Using those same mounting bolts (6), install the bagger
support mounts (4) onto the back of the unit.
Tighten bolts (6) to 40,7 Nm.
Reinstall bagger support tubes (5) into both bagger support
mounts (4). For both bagger support tubes, reinstall clevis
pins (2) and spring clips (3).
Retighten set screw (1).
CAUTION: Do not exceed 100 In-Lbs/11,2 Nm.
3
5
5
2
1
4
4
2
2
5
1
4
3
1
3
4
5
7
8
6
2
1
6
6
4
11
11
9
10
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna CTH194 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH194 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 10,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info