Manual Husqvarna 135 (page 17 of 420) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

477601

Zoom out

Zoom in

1/420

ASSEMBLY

English – 17

1154580-38 Rev.1 2011-12-05

Fitting the bar and chain

135, 140

Check that the chain brake is in disengaged position by

moving the front hand guard towards the front handle.

(38)

Unscrew the bar nut and remove the clutch cover (chain

brake). Take off the transportation ring (A).

(39)

Fit the bar over the bar bolt. Place the bar in its rearmost

position. Place the chain over the drive sprocket and in the

groove on the bar. Begin on the top side of the bar.

(40)

Make sure that the edges of the cutting links are facing

forward on the top edge of the bar.

Mount the clutch cover and remember to ﬁt the chain

adjuster pin in the hole in the bar. Check that the drive

links of the chain ﬁt correctly over the drive sprocket and

that the chain is correctly located in the groove in the bar.

Tighten the bar nut with your ﬁngers.

Tension the chain by turning the chain tensioning screw

cloc

kwise using the combination spanner. The chain

should be tensioned until it does not sag from the

underside of the bar.

(27)

The chain is correctly tensioned when there is no slack on

the underside of the bar, and it can still be turned easily

by hand. Tighten the bar nut with the combination spanner

while holding up the tip of the bar.

(28)

When ﬁtting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check the

chain tension regularly. A correctly tensioned chain

ensures good cutting performance and long life.

(25)

135e, 140e, 140e TrioBrake

Check that the chain brake is in disengaged position by

moving the front hand guard towards the front handle.

(38)

Loosen the chain tensioner wheel and remove the clutch

cover (chain brake). Remove the transport guard. (A)

(41)

Fit the bar over the bar bolts. Place the bar in its rearmost

position. Place the chain over the drive sprocket locate it

in the groove on the bar. Begin on the top edge of the bar.

(40)

Make sure that the edges of the cutting links are facing

forward on the top edge of the bar.

Mount the clutch cover and remember to ﬁt the chain

adjuster pin in the hole in the bar. Check that the drive

links of the chain ﬁt correctly over the drive sprocket and

that the chain is correctly located in the groove in the bar.

Tension the chain by turning the wheel down (+). The

chain should be tensioned until it does not sag from the

underside of the bar

(31)

The chain is correctly tensioned when it does not sag from

the underside of the bar, but can still be turned easily by

hand. Hold up the bar tip and tighten the bar knob by

turning the knob clockwise.

(32)

When ﬁtting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check the

chain tension regularly. A correctly tensioned chain

ensures good cutting performance and long life.

(25)

Fitting a spike bumper

To ﬁt a spike bumper – contact your service agent. (42)

WARNING! Always wear gloves, when

working with the chain.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 135 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna 135 Manual

Product: