729297
3
Zoom out
Zoom in
Previous page
1/3
Next page
Blinking: WPS interconnection verification is in progress. This process should not take
longer than 2 minutes.
Off: Wi-Fi function disabled
4
Voice indicator
On: Off-hook condition
Blinking: Incoming call
Off: On-hook condition
5
Signal indicator
On: Indicates network signal strength. Full light indicates strong signal.
Off: No network signal.
6
Micro SIM card slot
Accommodate a micro SIM card.
7
Wi-Fi button
Press and hold for less than 1 second to enable or disable the Wi-Fi function.
Note:
The CPE supports 2.4 GHz and 5 GHz Wi-Fi networks.
8
Reset button
Press and hold for more than 3 seconds to restore the CPE to its factory settings.
Note:
Restoring the default settings of the CPE will override all the previous settings.
9
WPS button
When WPS is enabled, press and hold the button for one to five seconds to set up a 2.4
GHz WPS connection, or press and hold the button for more than five seconds to set up a
5 GHz WPS connection.
10
Power button
Press this button to power the CPE on or off.
11
Power port
Connect to the CPE's power adapter.
12
USB port
Connect to a USB storage device or USB printer.
Note:
The CPE supports USB 1.1 and 2.0 storage devices in FAT16, FAT32, ext2, and ext3
formats. Storage devices with power supply requirements exceeding USB standards
may not work properly. It is recommended that you prepare an external power
supply in these cases.
The CPE is compatible with samba-supported USB printers.
This port cannot be connected to USB host devices, such as computers.
13
TEL ports (RJ11)
Connect to telephones or a fax machine.
Note:
Do not connect a telephone and fax machine to the CPE simultaneously.
14
LAN ports (RJ45)
Connect to computers, switches, or other network devices.
15
LAN4/WAN port (RJ45)
Connect to an Ethernet port, computer, switch, or other network device.
16
LAN4/WAN indicator
On: The port is connected to an Ethernet port or device.
Blinking: Data is being transmitted through the port.
Off: The port is not connected to an Ethernet port or device.
17
LAN indicators
On: The port is connected to a device.
Blinking: Data is being transmitted through the port.
Off: No device is connected to the port.
18
External antenna ports (SMA-J)
Connect to external antennas (optional).
Note:
Before you connect an external antenna to the CPE, remove the CPE's rear cover.
Getting Started
Installing the Micro SIM Card
Install the micro SIM card according to the illustration.
Note:
When removing the micro SIM card, gently press the micro SIM card in, then
release. The card will automatically pop out.
Do not remove the micro SIM card when the CPE is powered on. Doing so will
affect the performance of your CPE, and data stored on the micro SIM card may be
lost.
Connecting to a Power Adapter
Install the power adapter according to the illustration.
Note:
Use the provided power adapter. Use of an incompatible power adapter or one
from an unknown manufacturer may cause the CPE to malfunction, fail, or could
even cause a fire. Such use voids all warranties, whether expressed or implied, on
the product.
The CPE's power adapter model is HW-120200XYW. X and Y represent letters or
numbers that vary by region. For details about the specific adapter model, contact
an authorized dealer.
Logging In to the Web Management Page
The web-based configuration utility can be used for initial CPE installation, parameter
configuration, and function management through the browser.
The Windows 7 operating system and Internet Explorer 8.0 are used as an example. Ensure
that the CPE is connected to the computer. Follow these steps to log in to the web
management page:
1. Connect CPE cables.
2. Configure the computer's IP address so that the IP addresses of the computer and the
CPE are in the same network segment.
Note:
The CPE's default IP address is 192.168.8.1, the subnet mask is 255.255.255.0.
It is recommended that you use the automatically obtained IP addresses for the
computer and domain name system (DNS) server. If you manually configure the
computer IP address, you must set the DNS server IP address to the CPE's IP
address. Otherwise, you will fail to log in to the web management page.
3. Open the browser, and enter http://192.168.8.1 in the address box.
4. Enter the user name and password to log in to the web management page.
Note:
The default user name and password are printed on the CPE label.
LTE is a trademark of ETSI.
Version: V100R001_01 Part Number: 31010QQT
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huawei E5186s at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huawei E5186s in the language / languages: English as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info