Manual Hotpoint-Ariston AQC9 BF7 (page 4 of 20) (English)

665357

Zoom out

Zoom in

1/20

Installation

Where to put your dryer

• Place your dryer at a distance

from gas ranges, stoves,

heaters, or cooktops because

flames can damage the

appliance.

If you are going to install the

appliance under a work counter,

be sure to leave a 10 mm

space between the top and any

other objects on or above the

machine and a 15 mm space

between the sides and lateral

furnishings or walls. This is to

ensure proper air circulation.

Ventilation

• When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an environment

that is not damp and has proper air circulation throughout.

Airflow around the dryer is essential to condense the water

produced during the washing, the dryer will not operate

efficiently in an enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation will be experienced.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed behind a

lockable door, a sliding door or a door with a hinge on the

opposite side to that of the dryer door.

Water Drain

If the machine is positioned close to a drain it is possible

to drain the condensed water directly without using the

waterbottle. In which case it is no longer necessary to empty

the water bottle at the end of each cycle.If the Dryer is

positioned above or close to a Washing Machine the same

drainage can be used. Just unlink the tube indicated in figure

A and connect it to the drainage.

If the drainage is further away than the length of the tube it

is possible to buy and connect a tube of the same diameter

and the necessary length in order to reach the drainage.

To install the new tube just substitute the existing one as

indicated in figure B inserting it in the same place.

! The drain tube has to be below 1 m from the bottom of

the Dryer.

! Once the Dryer has been installed please assure that

the drain tube is not bent or contorted.

10 mm

15 mm

Electrical connection

Make sure of the following before you insert the plug into the

electrical socket:

• Ensure your Hands are dry.

• The socket must be grounded.

• The socket must be able to sustain the machine’s maximum

power, which is indicated on the rating plate (see Dryer Description).

• Power voltage must be within the values indicated on the

rating label (see Dryer Description).

• The socket must be compatible with the dryer’s plug. Should

this not be the case, replace the plug or the socket.

! Do not use extension cords.

! The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if exposed to rain or storms.

! Once installed, the dryer’s electrical wire and plug must be

within reach.

! The power cord must not be bent or squashed.

! The power cord is supplied fitted with a BS1363 plug and with

a 13 amp BS1362 fuse. If it is necessary to fit a replacement

fuse, it must be a 13 Amp ASTA approved to BS1362 type.

WARNING: The plug must not be used without a fuse cover.

If a replacement fuse holder/cover is required, it must be of the

same colour coding or wording as shown on the base of the plug.

Replacements are available from authorised dealers.

Changing the plug

The wires in the power cord are coloured in accordance with

the following.

! If the plug being replaced is a non-rewirable type, then the

cut-off plug must be disposed of safely. DO NOT leave it where

it can be inserted into a socket and create a shock hazard.

! The power cord should be checked periodically and replaced

by a cord specially prepared for this dryer and fitted only by

authorized technicians (see Service). New or longer power

cords are supplied at an extra charge by authorized dealers.

! The manufacturer denies any responsibility should any of

these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Before you start using your dryer

Once you’ve installed your dryer and before you use it, clean

the inside of the drum to remove any dust that could have

accumulated during transportation.

Moulded plug

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Green and Yellow (Earth)

wire to terminal marked “E”,

symbol x, or coloured green

and yellow.

Blue (Neutral) wire to

terminal marked ”N” or

coloured black.

13A ASTA approved fuse to

BS 1362.

Brown (live) wire to teminal

marked “L” or coloured red.

H<1m

Fig. A Fig. B

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston AQC9 BF7 in the language / languages: English as an attachment in your email.

The manual is 1,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint-Ariston AQC9 BF7 Manual

Product: