Manual Hitachi CF18DSAL (page 4 of 220) (All languages)

616693

Zoom out

Zoom in

1/220

English

Cutter block deformation

10. Prior to use, conduct a trial run. If during the trial run or

while using the tool, there are any indications of trouble,

abnormal sounds or abnormal vibrations, immediately

switch o the tool , discontinue use and arrange for

inspection or repairs with a Hitachi Authorized Service

Center. Continued use may result in injury.

11. If you accidentally drop or bump the tool, check it for

damage, cracks or deformities. If there are any, they may

result in injury.

CAUTION

1. Before operation, inspect the cutter block and housing

for loose bolts, hydraulic oil volume etc. Also, make sure

to remove any attached tools such as a wrench.

2. Make sure to remove the battery when inspecting,

cleaning or exchanging the cutter block. Accidentally

switching the tool on may result in injury.

3. Make sure there is nobody below when working in high

locations. Dropping the tool or other materials could

result in accident or injury.

4. Only use genuine hydraulic oil. The genuine oil must

be the equivalent of international ISO auxiliary viscosity

grade 46 (VG46).

5. If hydraulic oil comes into contact with eyes, do not rub.

Wash immediately and thoroughly with clean running

water and contact a physician for treatment. Left

untreated, the oil may lead to eye damage.

6. If hydraulic oil comes into contact with skin, wash

immediately and thoroughly with clean water and soap.

Failure to do so may lead to skin inﬂ ammation.

7. If hydraulic oil is accidentally swallowed, do not attempt

to vomit. Immediately contact a physician for treatment.

8. When hydraulic oil is not in use, make sure the lid of the

container is secure and store it in a dark place away from

direct sunlight and out of the reach of children.

9. Do not place the hydraulic oil container near a

combustion source such as heat, ﬂ ame or sparks. Doing

so may result in explosion.

10. Make sure the battery is securely attached. If not

securely attached, the battery could come loose and

cause injury.

11. Do not throw away battery with regular trash or dispose

in ﬁ re.

12. Store the battery in a location out of the reach of children.

13. Use the battery correctly in accordance with its

speciﬁ cations.

ADDITIONAL SAFETY WARNINGS

1. If the switch does not return to its original position,

immediately discontinue use and arrange for repairs with

the Hitachi Authorized Service Center.

2. Do not strike or apply strong impact to the switch panel.

Doing so can lead to damage.

3. While operating the tool:

 Make sure the rebar does not slant diagonally.

Rebar

 Keep the switch on until the piston reaches the tip.

 When switched on, the piston will not move forward until

it has completely returned. This is to ensure that the

next oil pressure is not applied while the hydraulic valve

inside the tool remains open.

4. Replace the blade at an early stage. Using a chipped

or deformed blade could result in injury from ﬂ ying

fragments.

5. Use the provided hex. bar wrench (4 mm) when installing

or removing the cutter block. Using a tool other than the

one provided may result in too much or not enough

tightening that can lead to injury.

6. When replenishing hydraulic oil:

 Always make sure it is done when the temperature of

both the tool and the hydraulic oil is cool. Removing the

oil plug while the tool is hot can result in the oil inside the

tool to spray out and cause accident or injury.

 Try to avoid inserting air when injecting the oil.

Pump case Hydraulic oil

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CF18DSAL in the language / languages: All languages as an attachment in your email.

The manual is 26,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi CF18DSAL Manual

Product: