616693
3
Zoom out
Zoom in
Previous page
1/220
Next page
3
English
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a quali ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and in rm persons away.
When not in use, tools should be stored out of reach of
children and in rm persons.
CORDLESS STEEL REBAR CUTTER
SAFETY WARNINGS
WARNING
1. Do not undertake tasks that go beyond the cutting
capabilities of this tool as listed in the speci cations
column. Also, do not cut hard materials whose tensile
strength exceeds 490 N/mm
2
. Doing so could result in
injury from ying fragments.
Rebar
490N/mm
2
2. Make sure to use the product with the anti-scattering
guard attached at all times. Never use the tool with the
guard removed.
Anti-scatter guard
3. Always wear a helmet, safety boots and other protective
equipment when working.
4. Hydraulic oil is ammable and the following precautions
should be taken to avoid re.
Do not remove the pump cases oil plug during operation
or when the tool is warm.
Replenish hydraulic oil after the tool has su ciently
cooled.
When replenishing hydraulic oil, choose a location
where there are no combustibles in the vicinity and
avoid any spilling. Should the oil be spilled, make sure to
thoroughly wipe it up.
Do not smoke when replenishing hydraulic oil or while
operating the tool.
Do not operate the tool near the location where hydraulic
oil was replenished.
5. When cutting rebar, make sure that the rebar is deeply
sandwiched between the cutting block. If not placed
deep enough, the cutter block may be damaged or
fragments may y, resulting in accident or injury.
Rebar
Cutter block
6. Never set the rebar in a slant where it sticks out above
the anti-scatter guard.
Rebar
Cutter block
Anti-scatter
guard
7. When operating the switch, never place your ngers
near the cutter block. Doing so can result in injury.
8. Do not cut rebar down to a length that is any shorter than
30 cm. Also, do not cut 2 or more rebars at one time.
Doing so can result in ying fragments that may result in
accident or injury.
Rebar
Rebar
Cutter
block
30cm
9. Do not use a damaged cutter block. Replace it with a
new one as a damaged cutter block will not only cause
damage to the tool, but accidents as well. If deformed,
the cutter block can be used by changing the direction in
which it is attached.
Cutter block
Cutter block
blade
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CF18DSAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CF18DSAL in the language / languages: All languages as an attachment in your email.

The manual is 26,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info