607815
4
Zoom out
Zoom in
Previous page
1/24
Next page
6
7
Lautstärke/Stummschaltung auf ein
bestimmtes Gerät programmieren
Halten Sie die Setup Taste (16) für ca.
3 Sekunden gedrückt, bis die rote LED
dauerhaft aufl euchtet.
Drücken Sie die Mute Taste (17) bis die
rote LED kurz erlischt.
Drücken Sie die Quellentaste für das
Gerät, das nur seine eigene Lautstärke-
und Stummschaltungsfunktion haben soll.
Drücken Sie die - Lautstärke Tasten (7) die
rote LED bleibt an.
Drücken Sie erneut die Mute Taste (17)
die rote LED geht aus.
Lautstärke/Stummschaltung wieder
zurücksetzen
Falls Sie die Lautstärke und Stummschaltung
wie in den vorangehenden zwei Abschnitten
beschrieben verändert haben, können Sie die
Funktionen wieder auf ihre Werkseinstellung
zurückstellen und so den „Punch-Through“-
Funktion wiederherstellen.
Halten Sie die Setup Taste (16) für ca. 3
Sek. gedrückt, bis die rote LED dauerhaft
aufl euchtet.
Halten Sie die Mute Taste (17) gedrückt,
bis die rote LED kurz erlischt.
Drücken Sie noch einmal die Mute Taste
(17), die rote LED erlischt.
Die Funktionen Lautstärke und
Stummschaltung „Punch-Through“- Funktion
ist jetzt wieder in den Auslieferungszustand
gesetzt.
Fehlerbehebung
Die Fernbedienung funktioniert nicht:
Überprüfen Sie, ob die Batterien der
Fernbedienung korrekt eingelegt sind und
die Polung +/– übereinstimmt.
Überprüfen Sie, ob Ihre Geräte korrekt
angeschlossen und eingeschaltet sind.
Falls die Batterien zu schwach sind,
tauschen Sie diese durch neue aus.
Es sind mehrere Gerätecodes unter
dem Markennamen meines Geräts
aufgeführt. Wie ermittle ich den richtigen
Gerätecode?
Um den richtigen Gerätecode für Ihr
Gerät zu bestimmen, probieren Sie die
Codes nacheinander aus, bis die meisten
Funktionen des Gerätes ordnungsgemäß
funktionieren.
Die Geräte reagieren nur auf einige Befehle
der Fernbedienung:
Testen Sie weitere Codes, bis die Geräte
auf die Befehle entsprechend reagieren.
Wenn die manuelle Codeeingabe und
die automatische Codesuche nicht zum
Erfolg führen, kann es in besonderen
Einzelfällen vorkommen, dass das Gerät
nicht kompatibel zu Ihrer Universal-
Fernbedienung ist.
g
Operating Instructions
Universal Remote Control
Function buttons
1. Power: ON/OFF
2. LED
3. Device keys
4. Numeric keys block 0-9
5. AV: switch over to external device
6. -/--: switch over to two-digit program
numbers
7. V+/V-: volume control
8. P+/P-: channel
9. navigation in screen-menus
10. OK: for the confi rming of inputs
11. E Fast rewind / red
B To playing / yellow
F Fast forward / blue
I record starting
K Stop / green
J Pause / magenta
12 . EXIT
13. EPG
14. screen-functions
15. Menu: device menu
16. Setup
17. H Muting
General
This universal remote control is one 5 in 1
remote control and can operate following
device types: TV, STB, AUX, VCR, DVD. (e.g.
DVD-recorder/Player, video recorders,
boosters, tuners, etc.).
The lettering of the keys does not describe
the device type to be programmed, it is used
therefore only for the easier overview.
Note down please the codes of your devices
which you used for the programming. If the
codes should be e.g. to a battery change no
more not stored, you can program the remote
control so more quickly.
They must program a four-digit device code
to a source key (TV, STB, AUX, VCR, DVD) for
every device which you would like to operate
with the universal remote control.
Video recorder: for the code search please
inserted a tape.
Programming device codes
Entering device code after code set
The codes of the corresponding devices are
the code list, to take that is enclosed in this
operating manual.
Turn on the device manually.
Press the source key (TV, STB, AUX, VCR,
DVD) shortly.
Hold the key setup (16) pressed for
approx. 3 seconds until the red LED lights
up permanently.
You distribute the corresponding four-digit
code then the code table one.
To the confi rmation of every keystroke the
red LED goes out shortly.
If the code input was valid, the red LED
goes out according to the input of the last
place.
Press shortly OK (10) in order to store the
code.
An invalid code was entered, the red
LED fl ashes for three seconds before it
goes out. Should the device not reacts;
you repeat the programming where
appropriate with another code. Please try
out all codes indicated for your brand.
Select the code which all available
commands of your remote control react to
correctly.
You should not have also any success in
this way, then you attempt it with that one
„search run automatic in the chapter“
described search method.
00040095bda.indd Abs1:6-Abs1:700040095bda.indd Abs1:6-Abs1:7 11.12.2008 11:59:14 Uhr11.12.2008 11:59:14 Uhr
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hama 40095 - 5in1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hama 40095 - 5in1 in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info