625851
35
Zoom out
Zoom in
Previous page
1/37
Next page
Mind to wear safety shoes to operate the plate vibrator – it is the only way of avoiding injuries and contusions
Prior to the commissioning
• manual and sure to follow safety instructions listed.
• Engine oil fill and oil level to ensure correct.
• Fuel (unleaded petrol) fill.
• Safety clothing
Installation and Commissioning (Fig. 1 / 2)
• Attach the handle (1) of the vibratory plates by screws on the guide bar (8).
Launch
• petrol tap (17)
• During cold engine WINDOW Choke, choke the engine in warm open (14)
• motor switch to "ON" (7)
• throttle slightly open (15)
• Starterseil draw - Note: If the oil level is too low the engine will not jump to.
• choke open while the engine warmläuft
• throttle fully open for operation
Parking
• Close throttle and idle speed to bring
• motor switch to "OFF" switch
• petrol cock closed
Step-by Step Instructions
1. Clear any foreign objects from the ground to be treated with the vibrator .
2. Always wear protection clothing .
3. Start the plate vibrator according to description in the manual. .
4. Observe all the relevant safety instructions and protection measures. .
5. Compact the ground to be treated slowly and evenly to obtain the best possible result.
Troubles-Causes-Troubleshooting
Trouble Cause Troubleshooting
Engine cannot be
started
1. Switch ON/OFF position .
2. No fuel
1. Refuel.
Engine runs unevenly
1. Engine gas lever still in the choke position .
2. Ignition plug loosened .
3. Dirty or dead fuel .
4. Jammed air filter .
5. Carburettor misadjusted .
6. Tank cover vent jammed .
1. Put the gas lever in position run.
2. Check the ignition plug .
3. Drain the dead fuel in a suitable container.
Pour fresh fuel in the tank .
4. Clean the air filter .
5. Have the carburettor adjusted .
6. Clean the tank cover and the vent .
Engine runs but the
machine will not be
vibrating
1. Not fully opened gas lever .
2. V-belt loosened or broken .
1. Open the lever at full .
2. Set up/replace V-belt (see inspections and
maintenance)
The plate slats or runs
unevenly
1. Loosened or damaged dampers .
2. Surface too hard .
1. Check the dampers, retighten or replace.
Inspections and Maintenance Safety Instructions
Turn the engine off before repairs, maintenance and leaving the vibrator .
Inspection and maintenance
V-belts
For new machines or installing a new belt, the belt tension after the first five hours of operation be reviewed. Then the belt every 50
hours of check and adjust.
Adjusting the strap
• The four screws on the strap loose and the protection belt protection decrease.
• The four screws that secure the engine to the console is attached, and the mother, with the rear part of the belt protection on the
console is attached, detach.
• The engine on the tightening of the belt to the rear (in the direction of handle), the loosening of the belt to the front slide.
35
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GRP 2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GRP 2500 in the language / languages: English, German as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info