637244

Graupner SPEED PROFI 40R - 7196 Manual

3
Zoom out
Zoom in
Previous page
1/6
Next page
Order-No. 7196
Operating instructions
SPEED PROFI 40RSPEED PROFI 40R
SPEED PROFI 40RSPEED PROFI 40R
SPEED PROFI 40R
Dear customer,
Many thanks for deciding to purchase this speed
control. This is a very high-performance product
incorporating the latest technology.
Please read through the instructions very carefully
before you use your new speed control. This
should ensure that you are able to exploit the
unit’s full potential, and avoid errors in its use.
Functions
• Auto Set-up
• High pulse frequency
• Forward, reverse with A.B.S. (Anti-Block braking
system)
• Delay time for reversing
• Overheating protection
Safety notes:
• No toy. Not suitable for children under 14 years.
• Read through the operating instructions carefully
before you use the unit.
• Exclusively for use in battery-operated radio-con-
trolled modells. No other usage is permissible.
• The permissible range is 4-10 cells. Never use
more than 10 cells.
• Be sure that the drive accu is not getting absolutely
empty when you drive. Otherwise the power supply
of the receiver is no longer ensured witch may
cause interferences in the receiver unit.
• Do not carry out any modifications of any kind to
the speed controller.
• All electric motors connected to the speed con-
troller must be of suitable rating and adequately
suppressed.
• Never operate your speed controller in or around
water. Dirt, water or other foreign matter must not
be allowed to get into the unit.
• Do not exceed the stated number of cells in the
battery.
• Motors fitted with propellers (boat or aircraft) are
hazardous objects which must be handled with
great care to avoid injury and damage. Never stand
in or close to the primary danger area of the motor
when the drive battery is connected to it. Any
electrical or mechanical defect may cause the motor
to burst into life unexpectedly, and parts may then
fly about which could cause serious injury.
• Disconnect the battery while charging or whenever
the speed controller is not to be used.
• Don’t switch on the speed controller until it is
plugged into the receiver, and the transmitter has
been switched on.
• Don’t touch the heat-sinks if they are hot, or are
heating up.
• Avoid short-circuits and reversed polarity connec-
tions between the cables, this will ruin your speed
controller immediately.
• Never run motor on external battery when hooked
up on speed controller.
• Always carry out a range check on the ground
before operating your model for the first time.
• Liability exclusion: We at GRAUPNER have no
control over the way you install, use and maintain
this speed controller, nor can we check that you
abide by the operating instructions. For this reason
GRAUPNER accepts no liability whatever for injury,
damage to property or financial loss which result
from the incorrect or improper use of this charger,
or are connected with it in any way.
Because we have no control over the installation
of this product, in no case shall our liability exceed
the original cost of the product.
Installing the Speed Profi 40R:
It is very important to determine the best possible
location for the speed control. Make sure that there
is the maximum flow of cooling air to the transistor
heat-sinks. Mount the speed control in the appropri-
ate position using double-sided foam tape.
Safety overheating cut-off:
If the speed control’s output stage threatens to over-
heat, a safety temperature cut-off switches off the
motor function until it has cooled down to a safe
level.
Installing the On/Off switch:
The On/Off switch can simply be fixed to any suit-
able point using double-sided foam tape.
Installing the receiver:
To avoid interference, please install the receiver as
far as possible from the motor, high-current cables,
batteries and the servo. The aerial should be run out
of the vehicle by the most direct route possible.
If the aerial is too long, it is best to simply cut off the
excess length.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner SPEED PROFI 40R - 7196 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner SPEED PROFI 40R - 7196 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info