656034
6
Zoom out
Zoom in
Previous page
1/8
Next page
- 09 - - 10 -
following formula to calculate the shutter speed required to capture the full sequence
of flashes:
Number of flashes / Firing frequency = Shutter speed
For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the
shutter speed should be at least 2 sec.
Note:
Stroboscopic flash is most effective with a highly reflective subject against a dark background.
Using a tripod and a remote switch is recommended.
A flash output of 1/1 or 1/2 cannot be set for stroboscopic flash.
Stroboscopic flash can be used with “buLb”.
Maximum Stroboscopic Flashes:
1/4
1/8
1/16
1/32
1/64
1/128
7
14
30
60
90
100
6
14
30
60
90
100
5
12
30
60
90
100
4
10
20
50
80
100
4
8
20
50
80
100
3
6
20
40
70
90
3
5
10
30
60
80
Flash Output
Hz
1 2
3
4
5
6-7
8-9
1/4
1/8
1/16
1/32
1/64
1/128
2
4
8
20
50
70
2
4
8
20
40
70
2
4
8
20
40
60
2
4
8
18
35
50
2
4
8
16
30
40
2
4
8
12
20
40
Hz
11 12-14
15-19 20-50
60-19910
Flash Output
Note:To avoid overheating and deteriorating the flash head during stroboscopic flash, do not use
stroboscopic flash more than 10 times in succession.
8. Hi-Speed Sync Triggering
To enter mode, press < > button (18) and hold
for 2 seconds.
To exit mode, press Mode Selection Button (11) or
press <  > button (18) and hold for 2 seconds again.
In hi-speed sync triggering mode, you can use a hi-
speed sync trigger to have your flash unit synchronized
When “OF” is shown on the LCD display, it means no flash output and flash firing is
turned off.
3. ZOOM: Setting the Flash Coverage
The flash coverage can be set to match the lens focal length from 24 mm to 105 mm.
Press < > button (12) and rotate Select Dial (14) to change the flash coverage.
4. M Mode: Manual Mode
Press MODE Selection Button (11) to enter M mode. In this mode, you can set the
flash unit onto your camera hot shoe or your trigger hot shoe for firing.
Before shooting, adjust the flash power output. When the camera's shutter is
pressed, the flash will fire synchronously. Slave triggering mode is not available in M
mode.
5. S1 Mode: S1 Slave Triggering Mode
Press Mode Selection Button (11) to enter S1 mode. In this mode, the flash unit can
function as a slave flash for creating multiple lighting effects. It is respectively
applicable to manual flash environment.
In S1 mode, the flash unit will fire synchronously when the master flash fires, the
same effect as that by the use of radio triggers.
6. S2 Mode: S2 Slave Triggering Mode
Press Mode Selection Button (11) to enter S2 mode. In this mode, the flash unit can
function as a slave flash for creating multiple lighting effects. It is applicable when
using a TTL master flash.
In S2 mode, the flash unit will ignore a single “preflash” from the master flash and will
only fire in response to the second, actual flash from the master.
7. RPT Mode: Stroboscopic Flash
Press Mode Selection Button (11) to enter RPT mode (Multi/Stroboscopic flash).
With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture
multiple images of a moving subject in a single photograph.
You can set the firing frequency (number of flashes per sec. expressed as Hz), the
number of flashes, and the flash output.
For setting procedures, see the following:
1. Press the Mode Selection Button (11) so that “RPT” is displayed.
2. Press Set Button (15) to select the item to be set. The item blinks.
3. Rotate Select Dial (14) to set a desired number.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing stops. Use the
Fn
ZOOM
Note:When setting the flash coverage, make sure it covers the lens focal length so that the
picture will not have a dark periphery.
Adjust power & high
speed triggering
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox V850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox V850 in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info