479887
9
Zoom out
Zoom in
Previous page
1/9
Next page
To reset the system proceed as follows:
Switch-off power supply
hort-circuit the RED and BLACK wires of the 2-way connector
Switch the on; once the alarm system is powered, 4 acoustic signals will sound and the turn
indicators will flash 4 times
Remove the previously created short-circuit; the status LED lights up steady.
reset is confirmed by an aucoustic signal and the wailing of the siren for
approx. 3 seconds
the LED will turns off. There are no acoustic signals
!
!
!
!
!
!
system .
S LED .
system
.
Turn ignition key “ON”;
.
Turn ignition key “OFF”; .
By activating the following procedure, the system returns to the
Factory default setting.
This procedure must therefore only be used in case of need, before programming the
system or auto-learning the turn indicators flashes.
!
15.0 -
15.1 - CO
15.2 - SENSOR ADJUSTMENT
I
.
T:
.
ULTRASONIC VOLUMETRIC PROTECTION
NNECTION AND POSITIONING
nsert the WHITE connector in the “W” marked socket and the RED connector in the “R” marked
socket (see figure below).
Install the transducers of the ultrasonic sensors on the top part of the windscreen internal pillars, away
from the air vents and orient them towards the center of the rear window
o check sensitivity level proceed as follows
With the alarm system disarmed, roll down the front window about 20 cm.
Adjust trimmer at a medium setting.
Close all doors, bonnet and boot and arm the system.
During the system inhibit arming time introduce an object in the cabin through the window and
move it around; the status LED will turn off to signal a presence.
If sensitity lelvel is too high or too low, readjust the trimmer and repeat the above procedure
!
!
!
!
!
ULTRASONIC
CELLS
CONNECTIONS
SENSITIVITY
ADJUSTMENT
PAGE 16 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 17
17.0 - TECHNICAL SPECIFICATIONS
Power supply
Current absorption @ 12Vdc with system armed and LED flashing
Working range temperature
Turn signals relay contact capacity
Engine immobiliser relay contact capacity
Alarm cycle duration
Maximum positive current output when armed (+A)
Maximum load of siren output
12 Vdc
15 mA
From -30°C to +70°C
8 A at 20°C
8 A at 20°C
30 sec.
700 mA
1A
16.0 - SYSTEM RESET
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 933 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 933 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 933

Gemini 933 User Manual - German - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info