479887
6
Zoom out
Zoom in
Previous page
1/9
Next page
9.0 - VEHICLE CODE PROGRAMMING
I
”.
f the system is to be managed via CAN-BUS line, it must be configured according to the vehicle on
which it is to be installed.
To help you understand the coding procedure, here below is an example illustrating the configuration
procedure.
In this case the code used is 1-0-3 which hypothetically corresponds to a “FIAT XXXXX
e area).
A separate leaflet, included in the alarm packaging, lists all the available vehicles
(codes are updated at packaging time).
Up-to-date information on supported vehicle models can be found at: www.gemini-
alarm.com (privat
!
!
Press the vehicle remote control lock/unlock buttons to make sure the alarm system works
properly.
Eventually disconnect the 8-way connector and reconnect it after few seconds
TEN FLASHES AND
A SHORT PAUSE
THREE FLASHES
ONE FLASH AND A
SHORT PAUSE
Connect the connectors of the wiring harness to the connector of the system.
.Press and hold the button shown below until the LED lights up
Release the button, the LED switches off.
After a 3/4 seconds pause, the LED starts the first sequence of flashes.
Press “1”.the button at the first flash which corresponds to number
After a 4 seconds, the LED starts the second sequence of flashes.
Press “0”.the button at the tenth flash which corresponds to number
After another 4 seconds, the LED starts the third sequence of flashes.
Push the button at third LED flashing, corresponding to value “3”.
When the last digit is entered, the alarm system “repeats” the entered code.
10.0 - SELF-LEARNING OF TURN INDICATORS FLASHES
In order to arm/disarm through the turn indicators, the system must learn the vehicle locking (arming)
and unlocking (disarming) flashes.
Connect the WHITE-ORANGE wire to the turn indicators and proceed as follows
Disconnect the 8-way wiring connector from the 8-way system connector.
Turn ignition key “ON”.
Connect the 8-way wiring connector to the 8-way system connector; the LED turns on steady.
urn ignition key
lose all doors and press the lock button on the original remote control.
When the turn indicators stop flashing, a high-pitched acoustic signal confirms the learning of the
arming flashes.
Press the unlock button on the original remote control.
When the turn indicators stop flashing, 2 high-pitched audio signals confirm the learning of the
disarming flashes.
This completes the procedure
!
!
!
!
!
!
!
:
T “OFF”.
C
.
!
!
To cancel the programming of the turn indicators reset the system (see
chapter 16.0).
Press
Press
Press
FIRST
FLASH
TENTH
FLASH
THIRD
FLASH
3-4 seconds
PAGE 10 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 11
!
The system has an indicator LED that signals any wrong vehicle code inserted.
The code must be range between 100 and 235 otherwise the LED on the unit blinks
repeatedly and the procedure is interrupted.
The previously inserted code remains stored.
The procedure is also invalidated if the LED blinks more than 10 times.
In this case there are no optical warnings, the procedure is simply be interrupted.
In either case, repeat the whole procedure.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 933 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 933 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 933

Gemini 933 User Manual - German - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info