479837

Gemini 7060 Manual

3
Zoom out
Zoom in
Previous page
1/9
Next page
Recapitulatory table of the programmable functions through the two -channels transmitter.
Function Manufacturer function Programmable function
1
Additional siren outlet Continuous sound Alternate sound
2
Acoustic signalling De-activated Activated
3
Boot opening with alarm disarmed De-activated Activated
4
Boot opening with alarm armed
With alarm disarmed if the 3
functions has been activated
Both functions
(Panic excluded)
5
Vehicle’s check De-activated Activated
6
Central door locking short period 0,5 seconds 1 second
7
Automatic arming Activated De-activated
8
Comfort While closing the doors After the blinker flashing
WORKING DESCRIPTION
- ALARM ARMING: press on the transmitter’s button N. 1. One pulse of the direction indicator lights signals
the arming.
- EXCLUSION OF THE VOLUMETRIC SENSOR, EXTERNAL SENSORS AND COMFORT CONTROL
AFTER THE ALARM ARMING: while alarm armed (even if the boot opening function with alarm armed is
activated), during the inhibit time (Led lightning fix) press on the transmitter 2 button. The exclusion is
signalled by one pulse of the direction indicator lights, the comfort function and the sensors are excluded.
This function de-activates at the first arming of the alarm.
- ALARM DISARMING: press on the transmitter’s button N. 1.
The disarming is signalled through 3 pulses of the direction indicator lights or 5 pulses if an alarm condition
has occurred.
SPECIAL FUNCTIONS
SELF-LEARNING OF THE CODE OF A NEW TRANSMITTER.
The self-learning of a new transmitter can be obtained with two different ways:
1. While alarm disarmed set the dip switch N.3 to ON and turn the ignition key to ON. The Led and the direction
indicator lights activate. Turning the ignition key to OFF the Led and the direction indicator lights switch off.
Press on the new transmitter button N. 1 within 8 seconds.
For each new code it is necessary to turn the ignition key to ON for one second and then to OFF.
At the end of the self-learning operation set the dip switch N.3 to OFF.
2. While alarm disarmed, open the driver’s door, turn the ignition key to ON and press on the coded transmitter
button N. 2. The Led and the direction indicator lights activate. Turning the ignition key to OFF the Led and
the direction indicator lights switch off. Press on the new transmitter’ s button N. 2 within 10 seconds.
For each new code it is necessary to turn the ignition key to ON for one second and then to OFF.
At the end of the self-learning operation, after 10 seconds the system works normally.
NOTE: the system is supplied with a maximum number of 3 transmitters.
AUTOMATIC ARMING
To obtain this function set the dip switch N. 2 to ON. 60 seconds after the disarming of the alarm, if the doors
and the boot are not opened and the ignition key is not turned to ON, the system will arm with or without closing
the vehicles doors (according to setting of the set-up 7 function).
REMOTE CONTROLLED BOOT OPENING.
The alarm unit 7060 allows opening the vehicle boot if the control is electric to negative. To obtain this function
select the set-up 3 function and press on the transmitter button N. 2 with the alarm disarmed.
If the boot opening is carried out pressing on the transmitter 2 button with the alarm armed (after selecting the
set-up 4 function), the panic function will de-activate and all the inlets inhibit for 60 seconds. If the boot is not
closed within this delay time the alarm will trigger. The opening of the boot through the transmitter is signalled
by one pulse of the direction indicator lights.
PANIC FUNCTION
To obtain this function with the alarm armed after the neutral time, press on the transmitter button N. 2 (if the 4
function- boot opening with alarm armed is de-activated). The siren, the klaxon and the direction indicator lights
activate. To de-activate this function within the 10 seconds of the alarm cycle, press on the transmitter button
N. 2.
LEDS MEMORY.
While disarming the alarm, turn the ignition key to ON to check if an attempted break-in has occurred.
Following the Led flashing it is possible to know the alarm triggering’s cause. The signalisation is repeated for
5 times.
Signalling LED Alarm triggering Alarm cycle
¬¬l¬¬ Door and boot/bonnet pin switches. 10
¬¬¬l¬¬¬ Ignition live Unlimited
¬¬¬¬l¬¬¬¬ External sensors 10
l LED OFF (2 seconds) ¬ LED ON (1 second)
Each alarm cycle is 30 seconds
The inhibit time is 30 seconds for all alarm triggering’s cause.
TRANSMITTERS BATTERY DISCHARGING
The discharging of the battery is signalled through the LED of the
transmitter. If the LED flashes while pressing one of the transmitter’s
buttons it is necessary to replace the batteries.
BATTERIES: CR1616
Note: put the batteries in the appropriate container.
TECHNICAL DATA
Power supply 10.5-14.5 V dc.
Working temperature -40° C + 85°C
Max. Current drawn alarm OFF 15 mA (with self-powered siren connected)
Transmitters frequency 433.92 MHz
Direction indicator lights relay contact capability 8A dc
Engine immobilisation relay contact capability 8A dc
Outlet horn relay contact capability 8A dc
Central door locking relay contact capability 8A dc
GEMINI 7147
DESCRIPTION.
GEMINI 7147 is 2 wires, high power electronic siren designed to be installed quickly and simply in the engine compartment.
WIRING CONNECTIONS (for the installer)
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
WIRE COLOUR FUNCTION
RED é Battery positive terminal (12V)
BLACK é To the alarm YELLOW -BLACK wire.
NOTE: connect the BLACK wire of the unit to earth.
INSTALLATION.
Install the siren in the engine compartment using the bracket and the screws supplied with the kit. Install the siren away from
areas of intense heat and turn to low the siren ear trumpet to avoid water infiltration.
Protect the wires from water and humidity and to avoid any damaging do not steam clean directly to the siren.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7060 in the language / languages: English as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info