544879

Geba Tronic DC 3 ECO - Standard - de Luxe Manual

18
Zoom out
Zoom in
Previous page
1/18
Next page
industrial controls
®
industrial controls
®
1918
S
t
a
n
d
a
r
d
connection pull switch
Connecting a pull switch
On the screw terminals 56 & 57 a pull switch (NO contact) can be connected.
56
57
automatic closing function (ON /OFF)
It is possible to switch or switch off the automatic closing time by connecting an external
timer to the screw terminals 54 & 55.
54
55
54
55
54
55
automatic closing function ON automatic closing function OFF
In the event of the automatic closing function being switched on permanently the screw ter-
minals 54 & 55 have to be bridged.
The function of the pull switch is
UP/STOP/DOWN/STOP.
Connecting a photo-cell (optional, only if Comfort module is connected!)
To connect a photo-beam to cover the ‘drive through’ area the photo-beam is connected to
the terminals 51, 52 & 53. If the infrared beam of the photo-beam is broken during the
DOWN direction the door will stop and reverse to a fully open position. It is possible to con-
figure the Comfort module so that when the photo-beam is activated by traffic the automatic
closing time is reduced to 5 seconds.
Using a photo-cell with receiver and transmitter, the power supply is connected to the
terminals 52 & 53.
51
52
53
NC
CC
GND
+
Spannungs-
versorgung
Steuerlogik
Connecting an opto-electric FRABA-Safety edge
It is possible to connect to the DC 3 an electric, pneumatic or opto-electronic (FRABA) type
Safety Edge device directly to the terminals 48, 49 & 50 without any specific control boxes.
The controlling of the safety edge is managed by the Comfort module and therefore there
is no need for an additional safety edge management device.
48
49 50
weiss
grün
braun
weiss grün
braun
Opto-electric safety edge - FRABA
terminal 48 = Safety edge (-GND)
terminal 49 = Safety edge (Signal)
terminal 50 = Safety edge (+ 15V)
Connecting an electro mechanical safety edge
(optional, only if Comfort module is connected!)
The controlling of the safety edge is managed by the Comfort module and there is therefore
no need for an additional safety edge controller.
For this purpose the DC 3 has an intelligent testing device which recognises when the door
has finished the closing cycle. In order to check it is necessary to connect a resistor on the
opposite end of the safety edge (cable connection).
48
49
8,2 kΩ
!
Connection of an electro-mechanical safety edge
Check settings of Jumper on
mainboard (see page 20)
and of DIP-Switches
on Comfort module
(see backpage )!
white
white
green
brown
green
brown
logic board
supply
voltage
Because the function of the safety-edges is automatically checked by the Comfort module
there is normally no need to test it. In this case the screw terminals 46 & 47 of the pre-limit
switch can be bridged. In situations where the rubber of the safety edge needs to touch the
ground you have to control this with a pre-limit switch (adjustment 5 cm above ground),
thus preventing the door to stop and return.
Connection pre-limit switch if using an electric- or opto-electronic safety edge
Connection of bridge on terminals 46 & 47
pre-limit switch.
46
47
… 18


Need help? Post your question in this forum.

Forumrules
1

Forum

geba-tronic-dc-3-eco---standard---de-luxe

Reset search

  • replacment had transmitters for gebatronic DC3 mini max 3 s Submitted on 31-1-2022 at 13:45

    Reply Report abuse

  • can i get replacemnt handheld transmitters for Gebatronic DC3 Mini Max 3S Submitted on 31-1-2022 at 13:44

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Geba Tronic DC 3 ECO - Standard - de Luxe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Geba Tronic DC 3 ECO - Standard - de Luxe in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Geba Tronic DC 3 ECO - Standard - de Luxe

Geba Tronic DC 3 ECO - Standard - de Luxe User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info