512654
15
Zoom out
Zoom in
Previous page
1/17
Next page
OFF the appliance immediately, pull the plug and dry the appliance with a clean cloth.
8. The motor block must only be wiped clean with a moist cloth. Do not clean the motor block
under flowing water, nor should it be immersed in water! Do not use alcohol, benzine, etc.!
9. Grease the mincer plate and knife with salad oil to prevent air corrosion.
Storage
Always clean the appliance before storing.
ATTENTION: Store and use the appliance in a clean, frost free environment where it is
protected from dampness, moistness and immoderate and extraordinary burden (such as:
downfall, beat, overheating, moisture in the motor block). Never lay heavy or hard objects
on top of the appliance.
10.Always assemble the appliance for storing. This way the parts are protected and can not
get lost.
ATTENTION: Never pull, rip, bend, clamp, squish or knot the line cord.
Trouble shooting guide
The mince is not fine enough.
There are still ingredients in the feed funnel
but no mince is coming out of the mincer.
The motor stops running while operating.
After cleaning the motor does not get started
again when turning the appliance ON.
Possible problem Easy solution
Disassembling
WARNING: To avoid injury and damages of the appliance turn the appliance OFF
and then wait for approx. 6 seconds to be certain that the motor is no longer
running. Always pull the plug before you start disassembling or cleaning
the appliance.
1. Switch off the mincer and disconnect the power supply cable
from the mains. Check that the motor has completely stopped.
2. Detach the mincer head from the motor block.
3. Unscrew the closing ring turning it counterclockwise.
TIP: If the closing ring is screwed on to tight you can use a
screwdriver as shown in the picture 10.
4. Remove the mincer plate. If necessary insert a knife or screw-
driver between the mincer plate and the mincer head to pry out the mincer plate.
5. Remove the crossed-blade knife and pull out the worm or if you used the chopper attachment
remove them.
TIP: If the tools are stucked knock the mincer carefully on a stable cutting board. The mincer
plate should be facing up.
ATTENTION: Be careful not to damage your bench top, the cutting board or the mincer.
6. Remove meat residues.
Operate as described:
ATTENTION: Never put the appliance or parts of the appliance
in the dishwasher or use abrasives for cleaning! This will cause
discoloration and corrosion.
7. Wash all parts thoroughly in hot soapy water. Do not use aggressive detergents. The parts
are not suitable for dishwasher. Soak parts with desiccated food leftovers a few minutes in
warm soapy water and use a nylon cleaning brush or cleaning sponge for cleaning. Rinse
all parts with running water and dry them accurately.
WARNING: Ensure that the switch and cable do not come into contact with water!
Should this inadvertently happen, all parts must be completely dry before the appliance is used
again. Never let water or other liquids run into the motorblock. Never clean the line cord
or the appliance in the dishwasher, poor liquids over the appliance or douse or dip it in water
or other liquids. In case that water or other liquids ran into the appliance while operating turn
Use a smaller mince plate and/or mince the ingredients more then
once.
The mincer is blocked. Turn the appliance OFF immediately and operate
according to the instructions ´Clear a blocking`.
The overload protection might got activated. Turn the appliance OFF
immediately and operate according to the instructions ´Clear a blocking`.
• Is the power cord plugged in?
The motor might be blocked with some hard substance (for example a
bone). Turn the appliance OFF immediately and pull the plug.
Disassemble and clean the appliance. Operate according to the
instructions ´Care and cleaning`.
If the problem is not solved after the cleaning, take the appliance
for technical maintenance and repair to an authorised specialised
reparation shop.
2928
41401_Manual_Neu.qxp 01.10.2008 15:40 Seite 28
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gastroback 41401 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gastroback 41401 in the language / languages: German as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gastroback 41401

Gastroback 41401 Manual - German - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info