Manual Gastroback 41401 (page 13 of 17) (German)

512654

Zoom out

Zoom in

1/17

Operating - Mincing meat

The mincer operates absolutely dependently and clean. If any problems should occur while

operating act upon instructions ´Trouble shooting`.

WARNING: For the case that liquid runs over the mincer while operating turn the mincer

OFF immediately and pull the plug. Clean and dry the appliance according to the

instructions ´Care and cleaning`.

TIP: If you use special mince-recipes you can mix the ingredients (for example steamed

onions or spices) with the meat before mincing. This way the ingredients get mixed really

well.

IMPORTANT: The mincer can not mince hard or stingily ingredients (for example: bones,

nuts, ginger). If you use hard ingredients like onions or carrots, you have to steam them before

adding them to the meet. Place a dry towel beside the mincer to dry off overrunning liquids.

1. Cut the meat into small pieces that will fit in the feed funnel and remove hard parts like

bones, shells or stems.

2. Assemble the appliance as described and place a plate or dish in front of the mincer head.

WARNING: Always make sure that the mincer is turned OFF before plugging in the power supply.

3. Plug the power supply cable into a mains socket and switch on the mincer.

WARNING: Never hold your face or other body parts over the feed funnel when the motor is

running because little pieces of food could be thrown out of the feed funnel. Never push the

food into the feed funnel with your fingers or put foreign substances (hair, towels, cutlery) into

the feed funnel. Always use the feedstick for this purpose!

4. Slowly feed the meat pieces into the feed funnel and push down

with the feedstick (see fig. 6). Do not apply excessive force when

pushing down the feedstick. Use only the feedstick to press down

the meat. Never use the fingers!

5. Switch off the mincer after use and disconnect the power

supply cable from the mains socket.

The mincer will easily continuously mince up to 30 kg of meat

(raw, cooked, different kinds of meat). 5 kg of raw meat are minced in 15 minutes max.

IMPORTANT: Operate in a slow and constant pace. Do not try to rush the procedure by

pushing down the meat with force. This way the worm might gets blocked and stops operating.

Only use the feedstick to slowly push down food through the feed funnel. If no meet is coming

2. Loosen the screw plug on the left side of the mincer turning it

anticlockwise. Firmly secure the mincer head in the opening for

the drive shaft. The opening of the mincer head should be

upright.

Hold the mincer head with one hand and insert the screw plug

into the side hole of the motor block. Turn the screw clockwise

(see. fig. 1) for tightening. Do not use force and be careful to not

overwind the screw thread.

WARNING: The blades of the crossed-blade knife are very

sharp. Pay attention when you handle the crossed-blade knife.

3. Insert the worm with the longer, narrower end into the mincer

head and turn slightly until it is securely seated in the mincer head (see

fig. 2). The sealing ring and then the grommet should be placed

at the narrow end of the worm. Make sure that the worm is placed

completely in the inside of the mincer head. If necessary turn the worm

a little bit to make it fit.

WARNING: Never use the crossed-blade Knife and the mincer

plate together with the chopper attachment. How to work with the

chopper attachment is explained within the recipe.

4. Mount the knife on the worm in the illustrated manner: The

rounded side of the knife must face the worm, the smooth side is in

contact with the mincer plate (see fig. 3). Meat will not be minced

if the knife is mounted the wrong way round.

IMPORTANT: If the tools overlap the edges of the mincer head

the worm is not placed all the way inside of the mincer head. Turn

the worm a little bit to make it fit inside but do not use force.

5. Mount the mincer plate on the knife. The two arresting pins

must lock precisely into the corresponding recesses (see fig. 4).

6. Firmly screw on the closing ring. Do not over-tighten (see fig. 5).

WARNING: Do not use any tools, for tightening the screw and pay

attention not to cant the screw. If the screw cants the screw thread

gets damaged. If the screw does not turn easily put some sunflower oil

(or other edible oil) on the screw.

7. Press the feed pan firmly onto the mincer.

8. Place the mincer on a firm base.

The mincer is now ready for operation.

2524

41401_Manual_Neu.qxp 01.10.2008 15:40 Seite 24

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gastroback 41401 in the language / languages: German as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gastroback 41401

Gastroback 41401 Manual - German - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info