3592
38
Zoom out
Zoom in
Previous page
1/132
Next page
ENGLISH
• 38 •
DESCALING SIGNAL
This function permits to reset the “DESCALING
message after descaling the machine.
• In the programming mode, press “
or
to select the function:
SIGNAL. DESCAL.
and enable it by pressing “ENT”.
The following message will appear:
SIGNAL. DESCAL.
NO
Press “
” or “
” to select the function:
SIGNAL. DESCAL.
YES
Press “ENT again to reset the scale counter.
Should this function be selected when the
message “DESCALING” is not shown on the
display, the following message will appear:
QUANTITY WATER
NOT REACHED
Press “ESC” to go back to the programming
mode.
Important: if you do not wish to reset
the counter, press “ESC”.
Important: after routine descaling, it
is recommended to reset the counter.
This will prevent you from forgetting to
descale the appliance.
TIMER
The machine can be programmed to switch
automatically from the
SELECT PRODUCT
READY FOR USE
function to the
ENERGY
SAVING
.
mode after a certain amount of time has
elapsed. The timer may be set from 0 to 12
hours, with 15-minute intervals.
The timer starts counting from zero after every
dispensing operation.
If “0:00” is shown, it means that the timer is off.
In the programming mode, press
or
to select the function:
TIMER
and enable it by pressing “ENT”. The display
will show:
STANDBY
AFTER 0:00
• Press
or
to select the desired time
and memorise the setting by pressing “ENT”.
RINSING CYCLE
With this function, all the coffee brewing parts
undergo a rinse cycle with water.
During the rinse cycle it is
recommended that a person be on
hand to supervise the operation.
To start the rinse cycle, press “
” or “
” to
select the function:
RINSING CYCLE
to enable the function press “ENT”. Press
“ENT” again to start the rinse cycle.
When the rinse cycle is completed, the
following message will appear.
FILL WATERTANK
At this point fill the water tank. The machine
will automatically switch to the normal
operating mode and the following message
will appear on the display:
SELECT PRODUCT
READY FOR USE
FACTORY SETTINGS
This function allows you to restore the default
machine operating parameters set by the
38

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggia Syncrony Digital at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggia Syncrony Digital in the language / languages: Dutch as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info