747920
65
Zoom out
Zoom in
Previous page
1/186
Next page
65
System menu
• Boost ON/OFF
OFF : It is the boost ON at the time of low-speed operation.(In the case of usual)
ON : It is always the boost ON.(When quick operation is hope)
• Damper
The characteristic when the servo is stopped can be set.
When smaller than the standard value, the characteristic becomes an overshoot characteristic. If the value
is larger than the standard value, the brake is applied before the stop position.
Especially, when a large load is applied, overshoot, etc. are suppressed by inertia and hunting may occur,
depending on the conditions. If hunting (phenomena which cause the servo to oscillate) occurs even
though the Dead Band, Stretcher, Boost and other parameters are suitable, adjust this parameter to a
value larger than the initial value.
[Relationship between damper set value and servo operation]
Small Value Setting
ĺ
When you want to overshoot. Set so that hunting does not occur.
Large Value Setting
ĺ
When you want to operate so that braking is not applied. However, it will feel like
the servo response has worsened.
(Note) If used in the hunting state, not only will the current consumption increase, but the life of the servo
will also be shortened.
• Stretcher
The servo hold characteristic can be set. The torque which attempts to return the servo to the target
position when the current servo position has deviated from the target position can be adjusted.
This is used when stopping hunting, etc., but the holding characteristic changes as shown below.
[Relationship between stretcher and servo operation]
Small Value Setting
ĺ
Servo holding force becomes weaker.
Large Value Setting
ĺ
Servo holding force becomes stronger.
(Note) When this parameter is large, the current consumption increases.
• Buzzer
When a servo is powered up without a transmitter signal, a buzzer sounds.
(When transmitter signal is lost, a buzzer sounds until the servo regains the signal. This is not unusual.
The transmitter has been turned OFF ahead of a servo power supply
The buzzer sound of about 1.25
Hz continues sounding as servo power supply end failure alarm.
(
Do not insert or remove the servo connector while the receiver power is ON.A buzzer may
sound by incorrect recognition.
)
*
Buzzer sound is generated by vibrating the motor of a servo.
Since current is consumed and a servo generates heat, please do not operate the number more than
needed or do not continue sounding a buzzer for a long time.
WARNING
While S.BUS servo writes, you aren't
supposed to remove a connection of a
servo and turn off a power supply of a
transmitter.
Data of S.BUS servo is damaged and breaks
down.
WARNING
Do not use the S.I/F (S.BUS servo setup)
connector with anything other than
high-voltage-capable servos.
Transmitter battery voltage is conveyed directly.
Using anything other than high-voltage-capable
servos presents the danger that they will break.
65

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-18SZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-18SZ in the language / languages: English as an attachment in your email.

The manual is 10,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba T-18SZ

Futaba T-18SZ User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info