522177
3
Zoom out
Zoom in
Previous page
1/5
Next page
WIRING
Ensure before any connection is made to the amplier or source unit, that you turn the audio system o. Failure to
do so could result in either the stock system or your new FUSION product being damaged.
FUSION will not warranty damaged ampliers due to incorrect installation.
Ground
When grounding your FUSION Amplier locate a metal area close to the amplier that is a good source of ground.
Use either a wire brush or sandpaper to eliminate unwanted paint, rust and corrosion. This will allow a better
contact for your ground. Use the same gauge cable for the ground as you did for the power. Secure the ground
cable using a solid connection. Spread silicon over the screw and bare metal to prevent corrosion.
NOTE: Each Channel 2 Ohms Stable
ie. 2 x 4 Ohm Speakers can be run in parallel o each channel
Channels cannot be bridged
Power
FUSION ampliers should be wired directly to the vessels battery using the appropriate sized cable. Start at the
vessels battery and run the power cable through to the amplier. FUSION recommends the use of grommets when
passing the power cable through any metal / bre glass walls, and to avoid sharp corners that may easily cut
through the insulation on the cable.
The use of an inline fuse at the battery position is essential. This will prevent the risk of a potential re caused by
a short circuit in your power cable. Connect the fuse holder as close to the battery positive terminal as possible.
You may now connect the cable to the battery, but remember to leave the fuse out or circuit breaker o until all
other cable connections are made.
Avoid running the power cable over engine components.
Remote Turn On
This wire must be connected to a switched +12V source, if the “Auto On/O” switch is located in the O position.
Typically, remote turn-on leads are provided at the headunit which will turn the amplier on/o in correspondence
with the source. If the head unit does not have a remote turn-on lead then a switched +12V supply can be used,
like the ACC +12V or alternatively turn the Auto On/O” switch to the ON position.
Auto ON/O
The Auto On/O switch allows an easy solution if a REMOTE wire cannot be used. When “ON” is selected the
amplier will turn on when an audio signal is detected from the source, when no signal is present the amplier will
automatically shut down after 1 minute. When O position is selected a Remote Switched +12V supply must be
used as described above.
Speaker Wiring
Choose the correct speaker wire for your application. Most applications will require a minimum of 16 gauge. Route
the speaker wire using the same precautions you did when you ran the power cables. Terminate these wires at
the speaker end using insulated speaker terminals (not supplied) or by soldering the connection. Make sure the
speaker connections are positive to positive and negative to negative. Ensure you have maintained the correct
polarity and balance.
Speaker Load
The Marine Zone amplier requires a minimum impedance of 2 Ohms STEREO (per channel) to operate trouble free.
WARNING: The Amplier CANNOT operate MONO!!!!! (bridged) This will result in damage to the amplier
Low Level Inputs
Choose the correct length and style of RCA interconnects for your needs.
Avoid running your RCAs near large wire looms and electric fans if possible. Be sure to check for correct balance.
(Red is right channel and Black or White is left channel).
Low Level Outputs
Use these RCA output connectors to connect to a secondary amplier.
004
WIRING
005
WIRING
AUX IN
YELLOW - Battery 12V DC (B+)
GREY
BLACK
WHITE
WHITE/BLACK
GREY
GREY/BLACK
BLACK - Negative Ground (B-)
LEFT SPEAKER
RIGHT SPEAKER
BLUE - Remote Turn On
AUX OUT
www.busse-yachtshop.de | info@busse-yachtshop.de
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fusion MS-AM702 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fusion MS-AM702 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info