20111
2
Zoom out
Zoom in
Previous page
1/2
Next page
Fujitsu DL3600 OSE
<CHR-SET> - SET1, SET2 *, ITALIC * GRAPHIC (unavail. for Epson emul.)‘
<AGM> (ii) - OFF *, ON
<PRF-SKIP> - NO-SKIP*, SKIP
<(page)WIDTH> - 13.6 inches *, 11.0 inches, 8.0 inches
<ZEROFNT> (iii) - NO-SLSH *, SLASH
<DC3-CDE> - ENABLE *, DISABLE
<CR-CODE> - (iii) ONLY *, CR&LF
<LF-CODE> - (iii)LF ONLY, LF&CR*
<RIGHTEND> - WRAP *, OVR-PRT (overprint characters at end-of-line)
(i) Not available for IBM XL24 emulation.
(ii) Alternate Graphics Mode available only for IBM XL24 emulation.
(iii) Not available for Epson emulations.
HARDWRE - Changes printer's hardware configuration.
<PPR-OUT> - CNTONLY *, DETECT, IGNORE
<PRT DIR> - BI-DIR *, UNI-DIR
<BUZZER> - ON *, OFF
<WORD LG> - 8BIT *, 7BIT
<(print )BUFFER> - 256BYTE, 2KBYTE, 8KBYTE, 24KBYTE
<FEEDER> - REAR * (no cut sheet feeder installed), SINGLE, DOUBLE
<FORMAT> - **8NONE1 *, 8NONE2, 8EVEN1, 8ODD1, 7EVEN1, 7ODD1,
7MARK1, 7SPACE1, 7EVEN2, 7ODD2
<BAUD RT> - 150, 300, 600, 1200, 4800, 9600 * ,19200
<PROTOCOL> - XON/XOFF *, DTR, REV-CHL (reverse channel), ETX/ACK
<DSR> - IGNORE *, DETECT
<DUPLEX> - FULL*, HALF
**Available only when a serial interface is installed.
LIST - Select to print a list of all current parameter settings.
DEFAULT - Select to reset MENU1 and MENU2 on control panel to factory
defaults.
SELF-TST - Select to run self-test. Prints the firmware version, resident emulations
and a continuous ASCII pattern. To pause self-test, press MODE or LF key. To
resume, press MODE or LF key again. To exit self-test and remain in setup mode,
press FF key. To exit self-test, save setup changes, and leave setup mode, press
ONLINE key.
V-ALMNT See "Critical Adjustments" below
TOF-ADJ - Set top-of-form with respect to top of physical page. Use ADJ to make
fine adjustments to top-of-form.
TOF-ADJ
Error Codes
When printer beeps four times and PAPER out light blinks, the printer hardware or a
font or emulation card is defective. If using a card, turn off printer, remove card and
clean gold contacts with a soft brush.
Common Problems and Fixes
Power does not turn on. Make sure power cord is securely connected to printer
and a working outlet.
Printer is on but does not print
1. Make sore printer is online and paper is loaded.
2. Make sure interface cable is securely connected at both ends.
3. If self-test does not execute normally, check interface, host, and printer and
software settings.
4. Make sure printer's emulation matches software.
Print quality is poor
1. Make sure paper thickness lever is set to match paper.
2. Make sure ribbon cartridge is properly installed.
3. Make sure ribbon feeds smoothly. Replace if worn.
Printing is erratic or wrong characters are printed
1. Make sure interface cable is securely connected at both ends.
2. Make sure emulation and, if applicable, serial settings on printer match host
settings.
Printing is vertically misaligned. Use V-ALMNT function (see "Printer Configura-
tion") to check and correct vertical character displacement.
Critical Adjustments
Vertical character displacement
1. Select V-ALMNT. Printer prints brief instructions and then starts printing rows
of parallel bars at letter quality speed.
2. If bars are offset to left (using first row as reference), repeatedly press MODE
key until bars are aligned. If offset to right, use LF key.
3. Press FF key to change speeds.
4. Repeat Steps 2 and 3 once to align bars at correspondence speed and again
to align bars at draft quality speed.
5. Press ONLINE key to terminate function, save new vertical alignment settings,
and exit setup mode.
Adjusting platen-to-print-head gap. The gap between platen and print head is
0.38 +/- 0.03 mm at both sides of platen.
1. Set paper thickness lever to position 1.
2. Set paper select lever to continuous forms.
3. Remove print head (see below).
4. Mount a gauge at print head position of carriage. Calibrate gauge using a
master gauge so that it reads zero (0.38 mm).
5. Move carriage to right and measure value indicated by gauge. Measure gap
while rotating platen by rotating idle gear and obtain average value.
6. Move carriage to left and rotate eccentric plate so that gauge indicates the
same value as that measured at right. Then fix plate in place.
7. Rotate the subassy. shaft so that the gauge indicates the value 0.38+1- 0.03
mm. (Plane surface is set vertically, close to main stay shaft.)
8. Replace gauge with print head and fix print head in place with mounting
screws.
Cover Removal
1. Pull off platen knob.
2. Open top cover and disconnect connector.
3. Push up top cover to remove.
4. Tip up cut sheet stand and pull up to remove.
5. Unplug two upper cover mounting screws at top front of printer and remove
upper cover.
Field Replaceable Units
Note:
Be sure to print a menu/configuration list before swapping printer.
DESCRIPTION OEM P/N
Print head D86B-1138-D783
Platen knob D860-1140-X514
Parallel interface board D05B-2903-D101
Serial interface board D05B-2903-D201
IBM P/N: 93F5997
IBM machine type: 1515-F19
Tech Support 800-877-7764
Item Options
<ORIGIN>** 1/6INCH, 1 INCH*, ADJ
<FINEAD> -7/60IN... +8/60IN
2 FJ-4 IBM/TSS Internal Use Only
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujitsu DL3600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujitsu DL3600 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info