20101
2
Zoom out
Zoom in
Previous page
1/5
Next page
Fujitsu DL2400 Dot Matrix Printer OSR
Initializing Interface Module
1. Turn on power while simultaneously pressing RESET button. The message
INITIALIZE PCB will appear on the display.
2. Press RESET button again and the message SAVING NOW!! will appear.
Serial Interface Requirements
Configuration adjustments are executed through control panel buttons.
Error Codes
Common Problems and Fixes
Power lamp not working:
1. Check power switch and power source.
2. Check operator panel.
3. Check AC fuse.
4. Check connections on PC board.
5. Remove and check AC inlet.
6. Check voltage selector jumper setting.
7. Check for defective interface board.
Power lamp working, but printhead not operational:
1. Check connectors from PC board to power unit.
2. Check mounting on PC and interface boards.
3. Turn power off to unit, unplug interface cable and re-start unit. If unit
responds check host system and cabling between host and printer. If unit
doesn't respond check DC voltage.
4. If message on display is "COVER OPEN ERROR" then check DC voltage:
a. Ensure top cover is closed.
b. Push the interlock switch. If "PRINT: OFF LINE" appears on display,
the interlock mechanism, cover or interlock assembly may be defective.
5. Check the interlock switch cable and for a possible short circuit.
Paper out error:
1. Set forms to continuous paper mode.
2. Check paper end detect mechanism.
3. Check the paper end switch assembly, cable and for a possible short circuit.
Feeder error:
1. Check main PC board.
2. Check cut sheet feeder.
Power lamp is working, but unit will not print:
1. If unit display shows "ON LINE: READY":
a. Check RS-232C interface cable.
b. Check interface cable.
c. Check for proper protocol selection.
d. Check for proper baud rate selection.
e. Check for proper data length selection.
f. Check for data format.
2. If unit display shows "PAPER OUT ERROR" follow "Paper out error" guide-
lines.
3. If unit display shows "FEEDER ERROR" follow "Feeder error" guidelines.
4. If unit display shows "ROM SUM" or "RAM R/W?":
a. Check main PC board.
b. Check interface board.
5. If unit display shows "DRIVER ALARM":
a. Check main PC board.
b. Check interface board.
6. If unit display shows "POWER ALARM":
a. Check power supply.
b. Check main PC board.
c. Check carriage motor.
d. Check paper feed motor.
7. If unit display shows "LEFT END ALARM":
a. Check carriage motor (ensure it is plugged in).
b. Check left end sensor.
c. Check PC board.
d. Check for melted fuse.
8. If the Centronic interface is selected then check the cable and cable con-
nections. If centronics cable is not selected then follow procedures for
checking DC voltage.
Unit not printing with display showing "ON LINE: BUSY ON LCD":
1. Check RS-232C interface cable.
2. Check interface cable.
3. Check for proper protocol selection.
4. Check for proper baud rate selection.
5. Check for proper data length selection.
6. Check for data format.
7. Follow procedures for checking DC voltage.
Bad print quality:
1. Check form thickness control quality.
2. Check adjustment on printhead.
3. Check to see that ribbon cassette is set properly.
4. Check ribbon for wear as well as ink density.
5. Check to see how ribbon is feeding through unit.
6. Check color mixing (if applicable).
7. Check the forms feed operation.
8. Check connection on interface cable.
9. Check for correct mode selection.
10. Check all connections on main PC board and power supply.
Bad color mixing in print quality:
1. Ensure ribbon cassette is mounted correctly.
2. Check paper thickness lever.
3. Check relation of shift lever and ribbon guide for proper settings.
4. Check adjustment on shift motor stopper.
5. Check shift belt adjustment.
6. Check ribbon guide height.
7. Check the shift motor.
Bad forms feed operation:
1. Check main PC and interface boards.
2. Check line feed motor.
3. Check wiring connected to line feed motor.
Intermittent form feeding problems:
1. Check positioning of forms.
2. Check platen gear backlash adjustment.
3. Ensure path has no obstructions.
4. Check main PC board.
5. Check line feed motor.
6. Check platen unit and other forms feed mechanism.
Printer Options
Cut sheet feeders
Optional Stacker
Field Replaceable Units (FRUs)
Transmission mode: Asynchronous, Full duplex
Speeds: 600, 1200, 2400, 4800 or 9600 (selectable)
Data bits: 7 or 8 bit selectable
Parity bit: Odd, even, mar, space or none (selectable)
Stop bit: 1 or 2 bit (selectable)
Protocol: 1. X-ON/X-OFF (DC1/DC3)
2. Data Terminal Ready (DTR)
3. Reverse Channel (RC)
4. ETX/ACK
Cover Door Open Front cover is open.
Paper Out Error Unit is out of paper.
Feeder Error Either printer is out of paper or has jammed in unit.
Set Friction Mode Cut Sheet Feeder is being used with paper release
lever set to continuous.
Open Paper Bail Paper bail is closed while auto-load switch has been
engaged.
Parity Error Printer has received incorrect data.
1. Check parameters of "FORMAT" or "BAUD RT"
2. Check Interface cable.
Framing Error Printer has sent information with incorrect data.
1. Check parameters of "FORMAT" or "BAUD RT".
2. Check interface cable.
Over-Flow Error Input buffer has overflowed.
1. Check parameters of "PROTOCOL", "FORMAT"
or "BAUD RT".
2. Check Interface cable.
Modem Error Printer has received data with bad modem control
signal.
1. Check parameter of "CONTROL".
2. Check Interface cable.
ROM Sum Error or RAM
R/W Error
Error has been detected on either RAM or ROM
memory.
Down Load Error Down load data format is incorrect.
Drive Alarm, Power Alarm
or Left End Alarm
These are warning indicators of possible mechanical
problems.
Description OEM P/N IBM P/N
A 24 Pin, 136 Column, Dot
Matr
N/A 11F9832
CM PCB I/F D05B-2880-6111 61H6104
CM PCB Main D16B-9557-0201 61H6103
Fan Assembly D860-9015-V561 61H6100
Motor Carriage D860-1140-T162 61H6101
Motor Paper Feed D860-1140-T142 61H6102
Platen D860-1140-T515 61H6107
Printhead D86B-1138-C523 61H6105
Sensor Left End D860-1140-V199 61H6106
2 FJ-8 IBM/TSS Internal Use Only
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujitsu DL2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujitsu DL2400 in the language / languages: English as an attachment in your email.

The manual is 0,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fujitsu DL2400

Fujitsu DL2400 User Manual - English - 182 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info