771574
5
Zoom out
Zoom in
Previous page
1/6
Next page
Replace UV-C Tube
Warning
Please cut off the power before replacing the UV-C tube.
Tools: Electric batch, Screwdriver, etc.
+
1
2
3
4
5
+
Duct
Duct
PCO-kit
PCO-kit
PCO-kit
M4 Srew
protective
net
protective
net
Screw
Screw
Base
Base
1. Conrm that the power is disconnected.Remove the 4 screws xing the PCO-kit
(keep the screws).
2. Remove the PCO-kit. Use a screwdriver to remove the screws that x the
protective net, and rotate the protective net in the direction of the arrow in the
gure 2, then slowly take out the protective net.
3. Pull out the UV-C tube slightly hard (do not damage the UVC-tube). Insert the
new UV-C tube into the lamp holder.
4. Insert the protective net and rotate the protective net in the direction shown in
Figure 4. When the screw holes on the protective device are aligned with the
screw holes on the base, use a screwdriver to lock the screws. Finally, x the
PCO kit back to the air duct.
5. Re-power on, turn on the power switch of PCO-kit, and use a small screwdriver
to hold down the reset button to make the digital tube display the value "8000".
Environmental Protection And Safety
Scrap Disposal: Treat separately with domestic waste and recy as much as possible.
The UV-C tube is broken treatment methods:
1. Open the window to ventilate as soon as possible.
2. Quickly clean up the debris and drop solid mercury, put the garbage bag
containing solid mercury in the outdoor waste lamp and battery treatment box.
3. Evacuate the personnel and do not get into the room within 15 minutes.
Fault Rectication
If the PCO-kit cannot operate after being powered on, please check the following
items. During the repair process, the disassembly and assembly steps are
involved, please refer to the UV-C tube replacement steps.
Fault Code Check steps
Check whether the wind speed sensor has a short circuit or an
open circuit.
1. Is the UV-C tube plugged in?
Pull out the UV-C tube again and insert it again.
2. The photosensitive components on the control circuit are
damaged. Replace the control board.
1. Check whether the PCO-kit is in good contact with the air
duct? No outside light affects PCO products.
2. Remove the protective net, pack the photosensitive
components with black insulating tape, power on to conrm
whether the alarm is cleared, if not cleared, replace the
control circuit board.
1. Conrm whether the electronic ballast connection line is
normal?
2. Replace with a new ballast of the same model
Replace the UV-C, and long press the Reset button to restore
the value of the digital tube to 8000.
67
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frigicoll PCO-Kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frigicoll PCO-Kit in the language / languages: English as an attachment in your email.

The manual is 3.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info