771574
4
Zoom out
Zoom in
Previous page
1/6
Next page
Instructions For Use
Note: The end of life of the UV-C tube will affect the sterilization effect. Be sure to
replace the UV-C tube.
hh
OFF ON
Set
Power
Life Span.
Error Code
PCO-kit
OFF ON
Set
Power
Life Span.
Error Code
PCO-kit
Power
Swicth Key
Power
Swicth Key
Digital
Tube
Digital
Tube
Set
Button
Set
Button
Power on, and turn on the PCO-kit power switch, the digital tube displays the
current mode: U1 mode or U2 mode (display 10s). This product defaults to U1
mode. If you need to switch to another mode, you can set it by pressing the
button "Set". When it is pressed for the rst time, the current mode is displayed
and blinks; when it is pressed for the second time, it switches to other modes.
Wait until it does not blink, then power off and Restart, PCO-kit will work in the
new mode.
In any mode, within 25s of starting the PCO-kit, the digital tube displays the life
value (no fault code is displayed), and the PCO-kit will work or standby (when
there is no wind in the air duct, the PCO-kit will be in standby) .
The difference between PCO-kit working in U1 mode and U2 mode is shown in
the table below.
System Monitoring Failure
Mode
Error Code U1 U2
Er-1
Er-2 X
Er-3 X
Er-4 X
Er-5
Note: means monitoring, X means not monitoring.
lnstallation Method
Warning
Please cut off the power before installation.
Installation tools:Impact drill, Electric batch, Wiring tool, 75mm diameter
iron hole opener, Screwdriver, etc.
1
2
3
1
2
3
4
4
5
6
1
2
3
4
>1.5m
Duct
Hole card Air outlet
Accessory
Port
Alarm Port
Control Port
Air conditioning
controller
Note: The equipment connection needs
to share the ground.
1. Paste the hole card on the air duct. And conrm that the distance between the
PCO-kit and the air outlet is greater than 1.5m.
2. Use a percussion drill to drill the hole, and the size of the hole is consistent with
that of the hole card.
3. Insert the PCO-kit into the air duct with the hole, and x it with 4 M4 screws.
(Note: When installing, the front direction should be easy to check.)
4. Make sure that the high-voltage power supply has been cut off. Connect the
alarm signal wire and control signal to the accessory prot. Insert the accessory
port into the signal port on the back of the PCO-kit in the direction of the notch.
(Note: The alarm signal line should be connected to the signal ports 1 and 2 of
PCO-kit, and the control signal line should be connected to the signal ports 3
and 4.)
5. Connect the power cord on the PCO-kit to the Mains grid distribution box, pay
attention to the yellow-green wire and ground wire.
6. Power on, turn on the power switch on the PCO-kit to the "ON" position, turn on
the air conditioner, and check whether it lights up normally after 30s.
(Note: When it is normally lit, the digital tube displays numbers)
45
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frigicoll PCO-Kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frigicoll PCO-Kit in the language / languages: English as an attachment in your email.

The manual is 3.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info