686544
4
Zoom out
Zoom in
Previous page
1/14
Next page
Frama F-Link
6
2.1 Wired operation
The F-Link supports operation with dynamic IP address assigned by a DHCP server or with a static IP ad-
dress configured via configuration page.
2.1.1 DHCP Mode
The factory default LAN connection type is DHCP (auto configuration). The F-Link can be connected to the
network with an active DHCP server as is described in the installation manual. After powering-up the F-
Link gets an IP address from the DHCP server in the LAN network.
In most cases no additional configuration is required and the F-Link operates with the franking system.
2.1.2 DHCP Mode with Proxy Server
If the internet connection is handled via proxy server, the proxy configuration has to be setup first.
For connecting to the configuration pages of the F-Link device, the dynamic assigned IP address has to be
known. Chapter 2.1.3 outlines, how this IP address can be identified.
The determined IP address can now be typed into the browsers address field to access the F-Link configu-
ration page. See Chapter 3 for further details.
2.1.3 Identifying the dynamic IP address of an F-Link device
Identifying this address can be done in several ways:
A) The IP address is shown as a part of the error message on the franking system.
If the F-Link device is not able to connect with the Frama FO2 server, a corresponding error mes-
sage will be displayed. Several messages show a hint for configuring of the F-Link. This hint in-
cludes the current IP address of the device!
B) The IP address can be find out by consulting a listing (e.g. arp table) which shows the assignments
between MAC and IP addresses inside a DHCP network. The MAC address of the F-Link can be
found at the sticker at the bottom of the device.
C) Finding the DHCP IP of the F-Link with the Frama F-Link IP Finder tool in your network.
Download the Frama F-Link IP Finder tool, which can be found at www.frama.com (down-
loads), to your PC
(Only Windows operating systems like Windows XP, Windows 7 are supported)
Start the Frama F-Link IP Finder tool
Enter the MAC address of the F-Link, which can be found at the sticker at the bottom of the
device.
Press the Search button
The Frama F-Link IP Finder tool scans all IP addresses in your network. If an F-Link was found
with this MAC address an entry will be showed in the result list.
The F-Link configuration page can be opened now with the default internet web browser on
your PC by clicking on the IP address in the list
Frama F-Link
7
2.1.4 Static Mode
The F-Link device can operate with a static IP address. The factory default LAN connection type is DHCP
(auto configuration).
Remark!
If the F-Link was used with LAN connection type DHCP or STATIC before for connections,
the access to the F-Link configuration page by the default IP address 192.168.1.200 and a
direct LAN cable is only possible after a reset of F-Link.
Changing to a static IP address is done in following steps:
1. Connect the F-Link device directly with a LAN cable to a PC
(A cross-wired LAN cable is needed if the PC doesn’t support auto-MDIX).
2. Note the PC LAN network settings for later use.
Set the PC LAN network settings as follow:
IP address: 192.168.1.199
Subnet mask: 255.255.255.0
3. Turn on the F-Link and wait until the Ready LED of the F-Link is on.
4. Open internet web browser on PC.
5. Insert the F-Link default IP 192.168.1.200 into address field.
6. Login with username and password. (Default username: “admin” and password: “admin”).
7. Open configuration page LAN Settings.
8. Change LAN connection type to “STATIC (fixed IP)”.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frama F-Link at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frama F-Link in the language / languages: English as an attachment in your email.

The manual is 2,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info