602510
58
Zoom out
Zoom in
Previous page
1/59
Next page
Wireless N300 High power Router
.
51
Appendix 2 FAQs
This section provides solutions to problems that may occur during installation and operation of the device. If your problem is not covered here,
please feel free to go to www.foscam.us to find a solution or email your problems to: support@foscam.us. We will be more than happy to help you
out as soon as possible.
1. Q: I entered the device’s LAN IP address in the web browser but cannot access the utility. What should I do?
a.Check whether device is functioning correctly. The SYS LED should blink a few seconds after device is powered up. If it does not light up,
then some internal faults may have occurred.
b.Verify physical connectivity by checking whether a corresponding port’s link LED lights up. If not, try a different cable. Note that an
illuminated light does NOT ALWAYS indicate successful connectivity.
c. Run the "ping 192.168.0.1" command. If you get replies from 192.168.0.1, open your browser and verify that Proxy server is disabled. In
case that ping fails, press and hold the "WPS/RST" button on your device for over 7 seconds to restore factory default settings, and then run
"ping192.168.0.1" again.
d. Contact our technical support for help if the problem still exists after you tried all the above.
2. Q: What should I do if I forget the login password to my device?
Reset your device by pressing the WPS/RST button for over 7 seconds.
Note:
All settings will be deleted and restored to factory defaults once you pressed the WPS/RST button.
3. Q: My computer shows an IP address conflict error after having connected to the device. What should I do?
a.Check if there are other DHCP servers present in your LAN. If there are other DHCP servers except your router, disable them
immediately.
b.The default IP address of the device is 192.168.0.1; make sure this address is not used by another PC or device. In case that two
computers or devices share the same IP addresses, change either to a different address.
4.Q: I cannot access Internet and send/receive emails; what should I do?
This problem mainly happens to users who use the PPPoE or Dynamic IP Internet connection type. You need to change the MTU size (1492
by default). In this case, go to “Internet Connection Setup” to change the MTU value from default 1480 to 1450 or 1400, etc.
5. Q: How do I share resources on my computer with users on the Internet through the device?
To let Internet users access internal servers on your LAN such as e-mail server, Web, FTP, via the device, use the " Port Range Forwarding r"
feature. To do so, follow steps below:
Step 1: Create your internal server, make sure the LAN users can access these servers and you need to know related service ports, for
example, port number for Web server is 80; FTP is 21; SMTP is 25 and POP3 is 110.
Step 2: Enter Port Range Forwarding screen from device web UI.
Step 3: Complete the Start Port (also called External/Ext Port on some products) and End Port (also known as Internal Port on some
products) fields, say, 80-80.
Step 4: Input the internal servers IP address. For example, assuming that your Web servers IP address is 192.168. 0.10, then simply input it.
Step 5: Select a proper protocol type: TCP, UDP, or Both depending on which protocol(s) your internal host is using.
Step 6: Click Enable and save your settings.
For your reference, we collected a list of some well-known service ports as follows:
Server
Protocol
Service Port
Web Server
TCP
80
FTP Server
TCP
21
Telnet
TCP
23
Net Meeting
TCP
15031720
MSN Messenger
TCP/UDP
File Send:6891-6900(TCP)
Voice:1863, 6901(TCP)
Voice:1863, 5190(UDP)
PPTP VPN
TCP
1723
Iphone5.0
TCP
22555
SMTP
TCP
25
POP3
TCP
110
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Foscam FR305 - N300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Foscam FR305 - N300 in the language / languages: English as an attachment in your email.

The manual is 5,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info