631010

Flymo UltraGlide Manual

6
Zoom out
Zoom in
Previous page
1/9
Next page
Removing and fitting the Blade and Fan
S
blade bolt
blade
fan
Switch off, wait until the blade has stopped rotating and
disconnect from the mains electricity supply BEFORE at-
tempting to remove or refit the blade.
Always handle the blade with care - sharp edges could
cause injury. USE GLOVES.
Removing the Blade and Fan (S)
1. To remove the blade bolt, hold the blade firmly with a
gloved hand and with a spanner, loosen the blade bolt
by turning it anti-clockwise.
2. Remove the blade bolt, washer and blade.
3. Inspect for damage and clean as necessary.
4. To remove the fan bolt, hold the fan firmly with a gloved
hand and with a spanner, loosen the fan bolt by turning
it anti-clockwise.
5. Remove the fan bolt, washer and fan.
6. Inspect for damage and clean as necessary.
7. In the event of a blade or fan becoming difficult to re-
move, insert a screwdriver (T1) into the hole (T2) to
lock the drive, then use a spanner (13mm A/F) to
loosen the blade bolt or fan bolt by turning the spanner
anti-clockwise. Ensure the screwdriver is removed be-
fore atempting to turn on the machine.
Renew your metal blade after 50 hours mowing or 2 years
whichever is the sooner - regardless of condition. If the blade
is cracked or damaged replace it with a new one.
Fitting the Blade and Fan (S)
1. Fit the blade to the shaft making sure you are able to
read the text on the blade ‘This side to grass’
2. Re-assemble blade bolt through the washer and the blade.
3. Hold the blade firmly with a gloved hand and tighten the
blade bolt firmly with a spanner . Do not over tighten.
1. Fit the fan to the shaft.
2. Re-assemble fan bolt through the washer and the fan.
3. Hold the fan firmly with a gloved hand and tighten the fan
bolt firmly with a spanner . Do not over tighten.
fan bolt
washer
1
2
T
Adjusting the Cutting Height
Cutting Height Adjustment
• Height of cut is adjusted by raising or lowering the
blade using the height adjustment lever (Q & R)
• There are four heights of cut on this product.
(13mm - 32mm)
•NOTE
A medium height of cut is recommended for most lawns.
The quality of your lawn will suffer and collection
will be poor if you cut too low.
Heights of cut:-
1 - low, 2 & 3 - medium, 4 - high
Q
R
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Flymo UltraGlide at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Flymo UltraGlide in the language / languages: English as an attachment in your email.

The manual is 3,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info