Electrical
1. The British Standards Institute recommend the use of a
Residual Current Device (R.C.D.) with a tripping current of not
more than 30mA. Even with a R.C.D. installed 100% safety
cannot be guaranteed and safe working practice must be fol-
lowed at all times. Check your R.C.D. every time you use it.
2. Before use, examine the cable for signs of damage or
ageing, If the cable is found to be defective, take the
product to an Authorised Service Centre and have the
cable replaced.
3. Do not use the lawnmower if the electric cables are
damaged or worn
4. Immediately disconnect from the mains electricity sup-
ply if the cable is cut, or the insulation is damaged. Do
not touch the electric cable until the electrical supply
has been disconnected. Do not repair a cut or dam-
aged cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your mower.
6. Keep cable away from lawnmower, always work away
from the power point mowing up and down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before
winding cable
for storage. Do not repair a damaged cable, replace it with
a new one. Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Our products are double insulated to EN60335. Under
no circumstance should an earth be connected to any
part of the product.
Preparation
1. While using your product, always wear substantial
footwear and long trousers. Do not operate the equipment
when barefoot or wearing open toe sandals.
2. Make sure the lawn is clear of sticks, stones, bones, wire
and debris; they could be thrown by the blade.
3. Before using the machine and after any impact, check for
signs of wear or damage and repair as necessary.
4. Replace worn or damaged blades together with their
fixings in sets to preserve balance.
Use
1. Use the lawnmower only in daylight or good artificial light.
2. Avoid operating your lawnmower in wet grass, where
feasible.
3. On slopes, be extra careful of your footing and wear
non-slip footwear.
4. Mow across the face of slopes, never up and down.
5. Exercise extreme caution when changing direction on
slopes. Walk never run.
6. Do not mow excessively steep slopes.
7. Do not walk backwards when mowing, you could trip.
8. Never cut grass by pulling the mower towards you.
9. Switch off before pushing the mower over surfaces
other than grass.
10. Never operate the lawnmower with damaged guards or
without guards in place.
11. Switch on the motor according to instructions and with
feet well away from the blade.
12. Do not put hands or feet near or under rotating parts.
12. Do not tilt lawnmower when the motor is running, ex-
cept when starting and stopping. In this case, do not
tilt more than absolutely necessary and lift only the
part which is away from the operator. Always ensure
that both hands are in the operating position before re-
turning the appliance to the ground.
13. Never pick up or carry a mower when it is operating or
still connected to the mains supply.
14. Remove the plug from the mains :
- before leaving the mower unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your lawnmower until
you are sure that the entire lawnmower is in a safe op-
erating condition;
- if the lawnmower starts to vibrate abnormally. Check im-
mediately. Excessive vibration can cause injury.
Maintenance and storage
1. Caution: Do not touch rotating blade.
2. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
3. Check the grassbox frequently for wear or deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement blade, blade bolt, spacer
and impeller specified for this product.
6. Be careful during adjustment of the lawnmower to pre-
vent entrapment of the fingers between moving blades
and fixed parts of the machine.
7. Store in a cool dry place and out of reach of
children. Do not store outdoors
8. Allow the product to cool for at least 30 minutes before storing.
CABLES - IMPORTANT
• Use only 1.00mm
2
size cable up to 40 metres length
maximum.
Maximum rating :
1.00mm
2
size cable, 10 amps 250 volts AC.
• YOUR PRODUCT IS SUPPLIED WITH AN
ELECTRIC
MAINS CABLE FITTED WITH A FEMALE CONNECTOR
.
1. If the supply cord is damaged, it must be replaced
by your local Husqvarna UK Ltd. Approved Service
Centre or similarly qualified persons in order to avoid
a hazard.
2.Flymo Extension Cables are available from your
local Husqvarna UK Ltd. Approved Service Centre.
3.Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna UK Ltd.
Approved Service Centre for further information on the
connectors and kits available.
4.Only use extension cables specifically designed for out-
door use and which conform to one of the following spec-
ifications: Ordinary rubber (60245 IEC 53), Ordinary PVC
(60227 IEC 53) or Ordinary PCP (60245 IEC 57)
CONNECTORS - IMPORTANT
• Flymo connectors are suitable for use with 2 core cable
only. Under no circumstances should these connectors
be used for earthed products.
• All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not be
left outside permanently nor should they be submerged
or immersed in water. Do not let cable lay or trail
through pools of water or splashed with water from hose
pipes.
MAINS PLUG REPLACEMENT - IMPORTANT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is in-
serted into a 13 amp socket.
1. No earth required. Flymo products are double insulated to
EN60335 and under no circumstances should an earth
be connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
The wires in the mains lead are coloured in accordance
with the following code:
BLUE - NEUTRAL
BROWN - LIVE
The wire which is coloured BLUE must be connected to
the Terminal which is marked with the letter 'N' or
coloured BLACK.
The wire which is coloured BROWN must be connected
to the Terminal which is marked with the letter 'L' or
coloured RED.
4. It is important that the outer sheath is clamped correctly
into the 3-pin plug.
5. If in doubt consult your local Service Repairer or quali-
fied electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
Cables
