389419
4
Zoom out
Zoom in
Previous page
1/5
Next page
12
Stickfi x coating.
Affi x the triangular abrasive STF-V93 to the tip
followed directly by a normal sanding strip STF-
93x178. In order to obtain maximum use of the
triangular abrasive it can be rotated at random
on the end of the sanding pad.
Please note
The STF-V93x266 sanding pad has been specially
developed for work in corners and on edges. Expe-
rience has shown that this leads to uneven stress
on the tip of the sanding pad. This inevitably leads
to the generation of more heat than when work-
ing on fl at surfaces since the same force has to
be distributed over a smaller surface. You should
therefore work with reduced pressure, otherwise
the Stickfi x coating on the sanding pad and abra-
sive can become damaged.
7 Attaching sanding material
Always use original Festool sanding ma-
terials!
7.1 Stickfi x abrasives
Self-adhesive abrasives such as Stickfi x
sandpaper and sanding fl eeces can be
attached to Stickfi x sanding shoes.
The abrasives (2.3) are simply pressed onto the
sanding shoe (2.4) and pulled off after use.
7.2 Abrasives to clamp
Festool offers perforated abrasives to
clamp.
Unperforated abrasives can be perforated with
the „Lochfi x“ (accessory).
Secure an abrasive sheet in place using the two
clamping devices (1.12). Press the levers to re-
lease the clamping devices.
Once clamped in position, make sure the
abrasive paper is taut and sits fl at on the
sanding pad.
8 lnstructions on application
Never overload the tool by using too much pres-
sure! The best sanding results are achieved
when applying moderate pressure. The sanding
performance and quality depend mainly on the
choice of the right sanding material.
We recommend the following settings on the
rotary control (2.1) for electronic machines:
rotary control setting
- sanding work
5 - 6
- sanding with max. drive
- sanding old paint
- sanding wood and veneer prior to painting
- interim sanding of paint on surfaces
4 - 5
- sanding of thinly applied primer
- sanding of wood with sanding vlies
- sanding edges on wooden parts
- smoothing primed wooden surfaces.
3 - 4
- sanding full wooden and veneer edges
- sanding in the grooves/rebates of windows and
doors
- interim paint sanding on edges
- pre-sanding natural wood windows with sanding
vlies
- smoothing wood surfaces with sanding felt prior
to staining
- rubbing down stained surfaces with sanding
vlies
- rubbing down or removing excess lime paste
with sanding vlies
2 - 3
- interim paint sanding on stained surfaces
- cleaning natural wood window grooves with
sanding felt
1 - 2
- sanding stained edges
- sanding thermoplastic synthetics
9 Maintenance and care
Always remove the power supply plug
from the socket before carrying out any
work on the machine.
The cool air openings in the motor casing must
always be kept clean and unobstructed to ensure
air circulation.
All maintenance and repair work which requires
the motor casing to be opened may only be carried
out by an authorised service centre.
10 Accessories, tools
Use only original Festool accessories and Festool
consumable material intended for this machine
because these components are designed specifi -
cally for the machine. Using accessories and con-
sumable material from other suppliers will most
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool rs 300 q-plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool rs 300 q-plus in the language / languages: English as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info