389419

Festool rs 300 q-plus Manual

3
Zoom out
Zoom in
Previous page
1/5
Next page
11
the power tool is used.
If the electric power tool is used for other ap-
plications, with other tools or is not maintained
suffi ciently prior to operation, however, the vibra-
tion and noise load may be higher when the tool is
used. Take into account any machine idling times
and downtimes to estimate these values more
accurately for a specifi ed time period. This may
signifi cantly reduce the load during the machine
operating period.
3 Power supply and start-up
The mains voltage must correspond to
the specifi cation on the rating plate.
Switch (1.1) serves as an On/Off switch (I = On / 0
= Off). It may be latched with the locking knob on
the side (1.2) for continuous operation. Pressing
the switch again releases the lock.
Always switch the machine off before
connecting or disconnecting the mains
lead!
See Fig. 3 for connection and disconnection of the
power cable.
4 Electronics
The RS 300 EQ has an electronic control
with which the rotational speed can be
varied step-free.
This allows the sanding speed to be adapted to
the optimum level according to the material con-
cerned (see Chapter 6).
The speed is set using the rotary control button
(2.1).
5 Dust extraction
Dust extractors prevent large accumu-
lations of dust in the air in the working
environment and dirt collecting at the
workplace.
5.1 Inboard extraction
The machines are fi tted with inboard extraction as
standard. The sanding dust is extracted through
suction openings in the sanding base (2.4) and
trapped in the turbo-fi lter (1.5). The turbo-fi lter
has to be changed when it is so full of dust that
the extraction power diminishes.
Inserting a turbo-fi lter
- Push the front cardboard section of the turbo-
fi lter with the sealing lip (1.4) onto the extraction
nozzle (1.9) of the fi lter holder
- Insert rear cardboard section with slot (1.6) onto
the retaining strip (1.7) of the fi lter holder
- Push the fi lter holder with its opening (1.11) as
far as it will go onto the extraction nozzle (1.3)
of the machine and clamp tight by turning rotary
knob (1.10).
5.2 External extraction by an extraction
unit
In order to avoid frequent changing of the turbo-
fi lter when carrying longer sanding jobs, it is
possible to connect a Festool extractor to the unit
instead of using inboard extraction. In this case,
the extraction pipe (Ø 27 mm (1.8)) of the extrac-
tion unit is connected to the suction nozzle (1.3).
6 Special sanding pads
The standard sanding pad (93 x 175 mm) can be
exchanged for a special sanding pad. Loosen the
four fastening screws (2.2).
The special sanding shoe is mounted in such a
way that the extended side protrudes over the
front edge of the sander.
6.1 Sanding pad STF-93x230
Please use the enclosed countersunk screws to
secure the STF-93x230 sanding pad instead of the
standard oval-head screws.
The special application of this sanding pad is to
sand in narrow spaces, e.g. between the louvers
on folding shutters or behind heating pipes.
The protruding part of the sanding pad is 60 mm
long and has a Stickfi x coating on the top and bot-
tom. Stickfi x sandpaper rolls in grit sizes P 50 to
P 180 are available for these applications. These
rolls are 12 m long and can be cut to the desired
length by the customer. Cut through the Stickfi x
adhesive coating on the back and the carrier
material using a sharp knife. The sandpaper can
then be simply torn off.
Please note that this sanding pad cannot be used
in conjunction with a suction unit.
6.2 Sanding pad STF-V93x266
The STF-V93x266 sanding pad is fastened with
standard oval-head screws.
This sanding pad has a protruding triangular point
with an edge length of 93 mm it was developed
for sanding in corners and edges though can also
be used on fl at surfaces thanks to its continuous
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool rs 300 q-plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool rs 300 q-plus in the language / languages: English as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info