458693
4
Zoom out
Zoom in
Previous page
1/24
Next page
4
Tool use and care
15 Use clamps or another suitable means to support
and secure the workpiece to a stable platform. Holding
the workpiece by hand or against your body is unstable and
may lead to loss of control.
16 Do not force the tool. Use the correct tool for your
application. The correct tool will do the job better and safer
at the rate for which it is designed.
17 Do not use the tool if the switch does not turn it on
or off. Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
18 Disconnect the plug from the power source before
making any adjustments, changing bits, blades or
accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
19 Store unused tools out of reach of children and
other untrained persons. Tools are dangerous in the hands
of untrained users.
20 Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting edges
are less likely to bind and are easier to control.
21 Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tools operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly
maintained tools.
22 Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used on
another tool.
12 Remove any adjusting keys or tools before turning
the tool on. A wrench or key that is left attached to a moving
part of the tool may result in personal injury.
13 Do not overreach. Stand on both feet and keep
proper footing and balance at all times. Proper footing
and balance enable better control of the tool in unexpected
situations.
14 Use safety equipment. Always wear eye and
hearing protection. Dust mask, non-skid safety shoes, and
hard hat must be used where conditions make them advisable.
Service
23 Tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified persons can result in a risk of injury.
24 When servicing a tool, use only identical
replacement parts. Follow the instructions in the
Maintenance section of this manual. Use of unauthorized
parts or failure to follow maintenance instructions may create
a risk of electric shock or injury.
SPECIFIC SAFETY RULES FOR CIRCULAR SAWS:
1 DANGER! Keep hands away from cutting area and
blade. Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they
cannot be cut by the blade.
Keep your body positioned to either side of the saw
blade, but not in line with the saw blade. KICKBACK
could cause the saw to jump backwards. (See Causes and
Operator Prevention of Kickback.)
Do not reach underneath the work. The guard can not
protect you from the blade below the work.
2 NEVER hold piece being cut in your hands or across
your leg. It is important to support the work properly to
minimise body exposure, blade binding, or loss of control.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool ATF 65 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool ATF 65 E in the language / languages: English as an attachment in your email.

The manual is 3,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info