763634
3
Zoom out
Zoom in
Previous page
1/12
Next page
22 Ferm
HYDRAULIC JACK
TECHNICAL SPECIFICATIONS
Fig.A
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance with
the instructions to make sure it functions properly. Keep this
manual and the enclosed documentation with the machine.
KNOW YOUR APPARATUS
Observe the instructions for maintenance to ensure
your apparatus always operates properly. Before
attempting to operate the apparatus, familiarise yourself
with the controls and make sure you know how to stop it
quickly in an emergency. Save this user’s manual and the
other documents supplied with this apparatus for future
reference.
SPECIAL SAFETY RULES
Non-observance of the following instructions can cause
personal injuries and/or damage to the vehicle.
1. Before jacking up the car, make sure the jack is as near
to the wheel to be lifted as possible and as far under
the body or any other point of support as possible.
2. The maximum load indicated on the jack must never
be exceeded.
3. The jack must be used as a lifting device only.
4. Always place the jack on a hard and level surface.
5. Always protect the car from rolling away. Before
jacking up the car, place chocks behind and in front of
the wheels remaining on the ground, if necessary. Put
the car in first gear or put on the handbrake to further
block the car.
6. Make sure to place the jack in such a way that your
hand is not underneath the car when jacking it up.
7. Make sure the jack is placed vertical.
8. For your own safety, before working or crawling
underneath the car jack up the car and support the
shafts.
9. Before using the shaft supports make sure they are in
good condition.
10. Should the pressure in the jack become too high,
excess air will escape through the relief valve. The
relief valve has been set in the factory.
BEFORE USING THE APPARATUS
ASSEMBLING THE JACKING BEAM
Telescope both parts of the jacking beam, allowing the
flat side to be used when opening and closing the cock to
lower the jack.
LIFTING
Put the car in '1' or engage the hand brake and block
the wheels to prevent the car from moving.
Close the cock by means of the jacking beam.
Instal the screw jack in the right place (indicated by
the car manufacturer).
Insert the jacking beam into the jacking point and
move the jacking beam up and down.
SHAFT SUPPORTS
After jacking up the car the shaft supports should be
installed.
Lower the car by turning the the screw of the release
valve anticlockwise, until the car rests on the sup-
ports. Never work under a car which only rests on
the trolley jack.
LOWERING
When you have finished the job, jack up the car until the
jack stands are free. Remove the jack stands. Using the
jacking beam, very slowly and counterclockwise open
the cock referred to under 2.
UK English
Ferm 3
ÉÄêÄçíàü
èÓ˜ÚËÚ „‡‡ÌÚËÈÌ˚ ÛÒÎÓ‚Ëfl ‚ „‡‡ÌÚËÈÌÓÏ
Ú‡ÎÓÌÂ, ÍÓÚÓ˚È ÔË·„‡ÂÚÒfl ÓÚ‰ÂθÌÓ.
å˚ Á‡fl‚ÎflÂÏ Ò Â‰ËÌÓ΢ÌÓÈ ÓÚ‚ÂÚÒÚ‚ÂÌÌÓÒÚ¸˛,
˜ÚÓ ‰‡ÌÌÓ ËÁ‰ÂÎË ÒÓÓÚ‚ÂÚÒÚ‚ÛÂÚ
ÌËÊÂÒÎÂ‰Û˛˘ËÏ ÌÓÏ‡Ï ËÎË
ÌÓχÚË‚Ì˚Ï ‰ÓÍÛÏÂÌÚ‡Ï:
EN1494
Òӄ·ÒÌÓ ÔÓÎÓÊÂÌËflÏ ‰ËÂÍÚË‚:
89/392/EEC
13-09-2002 „.
ÉÖçÖåéâÑÖç,
çˉÂ·̉˚
W. Kamphof
éÚ‰ÂÎ ÍÓÌÚÓÎfl ͇˜ÂÒÚ‚‡
CE
ı
ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ ВЕЛИКОБРИТАНИЯ
(RU)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm PKD-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PKD-20 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info