762292
5
Zoom out
Zoom in
Previous page
1/22
Next page
Never use the machine for grinding magnesium
workpieces.
SWITCHING ON
Slide the ON/OFF switch forwards.
The machine will start and keeps engaged when
releasing the switch
SWITCHING OFF
Press the ON/OFF switch: this will then jump to the
OFF-position.
Do not put the machine down when the motor is
still running.
OPERATION
Hold the machine firmly and move it against the
workpiece. Move the grinding disc evenly across the
workpiece.
Move the machine during roughing under an angle of
30º - 40º across the workpiece (fig. 6).
Never use grinding discs for roughing!
The machine must always work opposite to the
direction of rotation. Therefore, never move the
machine in the other direction! Otherwise, the
danger exists of it being pushed uncontrolled out of
the cut (fig. 7).
Inspect the grinding disc regularly. Worn discs have a
negative effect on efficiency of the machine. Replace
the grinding disc on time.
Do not put the machine down when the motor is still
running. Do not place the machine on a dusty
surface. Dust particles may enter the mechanism.
Always switch off the machine first before removing
the plug from the wall socket.
Never use the spindle lock to stop the motor.
TROUBLESHOOTING
1. Machine fails to operate:
Power turned off
(Extension) cable damaged
2. The elektromotor hardly reaches maximum
speed:
The extension cable is too thin and/or too long
The mains voltage is lower than 230 V
3. Machine overheats:
Air vents are blocked. Clean them with a dry cloth.
The machine has been overloaded. Use the machine
for the purpose it is made for.
4. Excessive sparking or elektromotor runs
irregular.
There’s dirt inside the motor or the carbon brushes
are worn. All parts represent an important part of
the double insulation system and should be serviced
only at our authorized service centers.
5. SERVICE & MAINTENANCE
MAINTENANCE
Make sure that the plug is removed from the mains when
carrying out maintenance work on the motor. The Ferm
machines have been designed to operate over a long
period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
CLEANING
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt. If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
LUBRICATION
The machine requires no additional lubrication.
FAULTS
Should a fault occur, e.g. after wear of a part, please
contact the service address on the warranty card. In the
back of this manual you find an exploded view showing
the parts that can be ordered.
ENVIRONMENT
To prevent damage during transport, the appliance is
delivered in a solid packaging which consists largely of
reusable material. Therefore please make use of options
for recycling the packaging.
Faulty and/or discarded electrical or electronic
apparatus have to be collected at the appropriate
recycling locations.
WARRANTY
The warranty conditions can be found on the separately
enclosed warranty card.
Ferm 5
Anvend aldrig maskinen til at slibe
arbejdsstykker i magnesium.
TÆND
Skub ON/OFF knappen fremad.
Maskinen vil starte og forbliver kørende når knappen
frigøres.
SLUK
Tryk på ON/OFF knappen: Denne vil så springe til
OFF-position.
Stil ikke maskinen ned når motoren stadig køre.
BETJENING
Hold maskinen med et fast greb, og fjern denne fra
arbejdsstykket. Bevæg slibeskiven med ens
bevægelser over arbejdsstykket.
Bevæg maskinen under slibning med en vinkel på 30º -
40º tværs over arbejdsstykket (fig.7).
Anvend aldrig slibeskiven til grovhugning!
Maskinen skal altid arbejde modsat
rotationsretningen. Træk derfor ikke maskinen i den
modsatte retning! Ellers kan den skubbes tilbage, væk
fra snittet, ude af kontrol
Efterse ofte slibeskiven. Nedslidte skiver har en
negativ virkning på maskinens effektivitet. Udskift
slibeskiven i god tid.
Stil ikke maskinen ned når motoren stadig køre.
Placér ikke maskinen på en støvet overflade.
Støvpartikler kan komme i kontakt med mekanikken.
Sluk altid maskinen før du fjerner stikket fra
stikkontakten.
Anvend aldrig aksellåsen til stoppe motoren
med.
HJÆLP
1. Maskinen fungere ikke:
Strømmen er slukket
(Forlænger) ledning er beskadiget
2. Den elektroniske motor når ikke op til
maksimumhastighed:
Forlængerledningen er for tynd og/eller for lang
Strømforsyningen er lavere end 230 V
3. Maskinen overophedes:
Udluftningskanaler er blokeret. Rengør dem med en
tør klud.
Maskinen er blevet overbelastet. Anvend kun
maskinen til det den er beregnet til.
4. Usædvanlig mange gnister, eller den
elektroniske motor køre uregelmæssigt.
Der er snavs inde i motoren, eller kulbørsterne er
nedslidte. Alle dele er vigtige dele i det
dobbeltisolerede system, og service bør kun udføres
ved et af vores autoriserede servicecentre.
5. SERVICE & VEDLIGEHOLDELSE
VEDLIGEHOLDELSE
Sørg for, at stikket til maskinen er taget ud af
stikkontakten, når der skal udføres vedligeholdelse på
motoren.
Ferm maskiner er blevet konstrueret, så de kan arbejde i
længere perioder med et minimum af vedligeholdelse.
Korrekt vedligeholdelse og rengøring af maskinen er en
forudsætning for lang tids tilfredsstillende brug.
RENGØRING
Kappen omkring motoren skal rengøres med en blød
klud, helst hver gang maskinen har været brugt.
Ventilationsrillerne skal holdes fri for støv og snavs. Hvis
snavset ikke vil gå af, bruges en blød klud vredet op i
sæbevand. Der må ikke bruges opløsningsmidler som
f.eks. benzin, sprit, salmiakspiritus o.l. Sådanne
opløsningsmidler kan beskadige dele af plastic.
SMØRING
Maskinen skal ikke smøres.
FEJL
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed,
kontakt venligst serviceadressen på garantibeviset. På
bagsiden af denne manual finder du en tegning med alle
dele, der kan bestilles.
MILJØ
For at undgå transportbeskadigelse leveres maskinen i
en solid emballage. Emballagen er så vidt muligt lavet af
genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller
elektroniske maskiner skal afleveres på en
genbrugsplads.
GARANTI
Garantibetingelser er beskrevet på det separat vedlagte
garantibevis.
40 Ferm
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm AGM1002 FAG-125N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm AGM1002 FAG-125N in the language / languages: All languages as an attachment in your email.

The manual is 5,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info