Manual Felisatti RGF150 (page 4 of 26) (English, German, French, Italian, Portuguese, Spanish)

502503

Zoom out

Zoom in

1/26

are given below: the lead in lead-based paint, crystalline

silica from bricks and cement and other masonry prod-

ucts, and also arsenic and chromium from chemically

treated wood. The risk deriving from this type of expo-

sure varies and depends on the frequency with which

this type of work is carried out. In order to reduce expo-

sure to these chemical agents: work in a well ventilated

area and work with approved safety equipment, such as

face masks which are specially designed to filter out

microscopic particles.

 WARNING! Pregnant women and children should not

enter any area where paint is being sanded until it has

been thoroughly cleaned. Pregnant women and chil-

dren are at greater risk from lead poisoning.

 Use the tool for dry sanding only. If water enters the

tool there is an increased risk of electric shock.

BRIEF DESCRIPTION

Rotorbital sanders have circular bases that make small,

very fast circular movements. The result is very smooth,

scratch-free. Most tools have a perforated base through

which dust is vaccumed, when using perforated abrasive

sandpaper. They are used to obtain a fine finish.

WARNING! Any use differing from the above is strictly

forbidden.

Use only for the following types of work:

1. Finishing of wooden surfaces, synthetic material,

metal and painted surfaces.

2. Removing rust and finishing steel surfaces.

BEFORE USING THIS TOOL

Before using the tool, make sure the mains voltage is

correct: it must be the same as that on the specification

label. Machines with 230V can also be connected to a

220-V mains supply.

FITTING SAFETY DEVICES

WARNING! Always unplug the machine before carrying

out work on it.

Use of the auxiliary handle is obligatory in order to ensure

greater control and safety when handling the tool.

FITTING THE ACCESSORIES

WARNING! For safety reasons, you should always

disconnect the apparatus from the power source

before proceeding to change the plate. Always wear

safety goggles.

Immediately substitute a damaged plate.

WARNING! Never press the blocking button when the

machine is running. The shaft must have stopped com-

pletely before the blocking button is pressed.

For changing the Velcro plate, proceed in the following

manner:

1. Block the spindle (shaft) by pressing blocking button

C and with one hand unscrew the plate.

In order to mount the plate, proceed in reverse order.

2. Once the disc is fitted, check that the blocking button

has returned to its original position due to movement

of the incorporated spring.

MOUNTING OF SANDPAPER SHEETS

WARNING: Whenever you work on the machine, always

unplug it first.

First select the right grain of sandpaper for the surface to

be sanded.

These sanders incorporate a sandpaper with Velcro

attachment system that is attached directly to the

plate. In order to assure an optimal dust aspiration, the

holes of the sanding sheet should coincide with the

holes of the plate.

STARTING THE TOOL

WARNING! Check that the mains voltage is the same as

that in the machine’s specifications.

Plug the machine in with the switch off.

Start the machine by turning the switch A to position

"ON". To switch off, do the same in reverse.

Constant electronic performance and speed adjustment

The built-in module enables soft start and for the rated

speed to be maintained practically constant until the

rated power is reached.

The electronic speed regulator enables the speed to

be set to different positions from 1 to 6. The most

appropriate speed should be selected according to the

part to be polished.

PRECAUTION: The speed regulator can only be turned

to position 6 and then be returned to position 1. It must

never be forced beyond 6 or 1, since this could cause

damage to the machine.

WORKING INSTRUCTIONS

Do not use the sander without the abrasive disk.

Move the sander over the entire surface to be sanded.

Its weight is pressure enough. Extra pressure merely

slows the sanding action and produces an irregular

finish, in addition to wearing out the sander and sandpa-

per. Do not leave the machine in operation by itself since

it will over-sand the surface.

Always switch the sander on before placing on the

surface to be sanded. Never switch off the sander when

positioned on the surface: first lift off and then switch off.

Do not use the sander without sandpaper since this

would damage the supporting pad. Keep hands away

from the air holes and ensure that neither oil nor water

can penetrate into the motor.

Attention: do not let the spinning disk touch sharp

protrusions, screws, nails, etc., because they could

cause damage.

Use sandpaper discs which are suitable for the surface

to be worked and the required results.

PRECAUTION: During polisher operation, the electri-

cal cable should always be kept behind to prevent it

being trapped.

DUST EXTRACTION

WARNING! Always make sure that the tool is switched

off and unplugged before fitting or removing any dust

extraction device.

Dust extraction keeps the workplace clean, prevents

dust build-up in the air and facilitates waste elimination.

These sanders are provided with a dust aspiration

output which adapts to a universal vacuum or any other

dust aspiration device.

CAUTION: Always use an aspiration extractor designed

according to the guidelines applicable to dust emission.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti RGF150 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti RGF150 Manual

Product: